1、Designation:D522616Standard Practice forDissolving Polymer Materials1This standard is issued under the fixed designation D5226;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicate
2、s the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice outlines the parameters applicable to thepreparation of a polymeric solution,such as solvent,concentration,temperature,pressure,time,agitation,and heat-ing
3、 mode.1.2 The proper use of this practice requires knowledge ofsolvents and their effect on polymeric materials.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety
4、 and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-tics2.2 Other Do
5、cument:Polymer Handbook33.Terminology3.1 Definitions are in accordance with Terminology D883.3.2 Abbreviations are in accordance with TerminologyD1600.4.Summary of Practice4.1 A polymer solution is described or prepared using thecell classifications listing the parameters relative to solvate thepoly
6、mer.The cell classifications are listed in the followingorder:polymer,solvent,concentration,temperature,time,container,heating mode,and agitation.4.1.1 A polymer and a list of suggested solvents for makinga solution are listed in Annex A1.4.1.2 Table 1 designates the parameters for container,heat-in
7、g mode,and type of agitation.NOTE2To illustrate the use of the cell classifications with Table 1,a2%solution of poly(vinyl chloride)using cyclohexanone would bewritten as:PVC2 cyclohexanone2 202 662 402 BECwhere:PVC=abbreviation of the polymer from Annex A1,cyclohexanone=the solvent from Annex A1,20
8、=weight of polymer in tenths of a percent,66=temperature in degrees Celsius,40=time in tenths of an hour,B=glass container from Table 1,E=bath heater from Table 1,andC=random agitation from Table 1.5.Significance and Use5.1 This practice embodies the specifications to describe thepreparation of a po
9、lymeric solution.6.Procedure6.1 PolymerSelect the applicable polymer fromAnnexA1and write its abbreviation.6.2 SolventSelect the solvent applicable to the polymerfrom Annex A1.6.3 ConcentrationWrite the polymer gram weight intenths of a percent per milliliter of solvent.6.4 TemperatureWrite the solu
10、tion temperature in degreesCelsius.6.5 TimeWrite the time for solution in tenths of an hour.6.6 ContainerSelect the type of container from Table 1.6.7 Heating ModeSelect the heating mode from Table 1.6.8 AgitationSelect the agitation mode from Table 1.7.Precision and Bias7.1 No statement is made abo
11、ut the precision or bias of thispractice since the procedure is descriptive with no measure-ments being made.1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.70 on Analytical Methods.Current edition approved Sept.1,2016.Pub
12、lished September 2016.Originallyapproved in 1992.Last previous edition approved in 2010 as D5226-98(2010)1.DOI:10.1520/D5226-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,re
13、fer to the standards Document Summary page onthe ASTM website.3Available from John Wiley and Sons,New York,NY.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 8.Keywords8.1 p
14、olymer solutions;solution preparation;solutions;sol-ventsANNEX(Mandatory Information)A1.SUGGESTED SOLVENTS FOR POLYMERIC SOLUTIONSA1.1 Note the following:A1.1.1 The solvents in Table A1.1 are listed in randomorder.A1.1.2 An increase in polymer molecular weight reducessolubility.A1.1.3 Branching incr
15、eases the solubility compared to alinear polymer of the same molecular weight.A1.1.4 Solubility normally increases with rising tempera-ture.A1.1.5 The temperature is for room temperature unlessnoted.A1.1.6 The following abbreviations are used in Table A1.1:D.S.=degree of substitution,S.C.=substituen
16、t content,conc.=concentrated.TABLE A1.1 SolventsAbbreviationPolymerSolventsABAAcrylonitrile-butadiene-acrylatearomatic hydrocarbons,chlorinated hydrocarbons,tetrahydrofuran,esters,ketones,N,N-dimethylformamide,N,N-dimethyl-acetamide(ifhigh acrylonitrile)ABSAcrylonitrile-butadiene-styreneN,N-dimethylformamide,N,N-dimethylacetamide(if high acrylonitrile),cyclohexanone(above 35C),cyclohexanone/acetone,methylcyclohexane/acetone,decahydronaphthalene/dimethyl oxalate,benzene,toluene,ethylbenzene,styre
