1、Designation:D4825 97(Reapproved 2007)An American National StandardStandard Test Method forMeasurement of Curl in Cut-Sized Office Paper1This standard is issued under the fixed designation D4825;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the measurement of curl incut-sized office papers at ambient conditions.The te
3、st methodwould typically be used in evaluating papers described inSpecification D3460 or after processing in a copier or printingdevice.1.2 Cut-sized office papers are generally described as hav-ing dimensions of 812by 11 in.,812by 13 in.,812by 14 in.,and 11 by 17 in.1.3 This standard does not purpo
4、rt to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D528 Tes
5、t Method for Machine Direction of Paper andPaperboardD585 Practice for Sampling and Accepting a Single Lot ofPaper,Paperboard,Fiberboard,and Related ProductD685 Practice for Conditioning Paper and Paper Productsfor TestingD3460 Specification for White Watermarked and Unwater-marked Bond,Reprographic
6、,and Laser Printer Cut-SizedOffice Papers3D5039 Test Methods for Identification of Wire Side ofPaper33.Summary of Test Method3.1 A lift of approximately 10 to 20 sheets of paper areremoved from a sealed ream and the curl is measured notingthe axis,direction,and magnitude of the curl.3.2 The tests ca
7、n be conducted at 50%relative humidity orat ambient conditions if it is carried out quickly.4.Significance and Use4.1 Curl in cut sized paper plays an important part in howpaper performs in its intended use.Frequently cut-sized papersare used in duplicators and copy machines operating at highspeeds.
8、Inherent curl,that is,curl in the ream before enteringthe process and curl developed during the imaging process,canaffect its performance,especially if duplexing(two-side print-ing)or collating is involved.Common problems experiencedinclude jamming and misregistration.4.2 The experience used in deve
9、loping the test method waslimited to uncoated writing papers in the commonly used cutsizes.The technique is basic and could be used with coatedpapers as well as paperboard to identify the type and magnitudeof curl.4.3 The test method identifies the type and degree of curl ina pack of sheets and does
10、 not address variations that might beinherent in individual sheets.If during the testing process it isobserved that one or more sheets reacts in a contrary manner tothe lift,it should be noted.Curl of a single sheet may notnecessarily be determined by this procedure.5.Apparatus5.1 Curl GaugeA curl g
11、auge can be developed whichconsists of a straight line 216 mm(812in.)long and companionarcs each 216 mm(812in.)long of a radius such that thedistance between the arc and the chord intersecting the arccircumference at the 216-mm(812-in.)length is 10 mm,15mm,20 mm,and 30 mm.An example of such a gauge
12、is shownin Fig.1.NOTE1Copies made on a xerographic copier of the curl gauge shouldnot be used because those devices frequently have a built-in enlargementwhich would change the dimensions of the arcs.A curl gauge can bedeveloped using the following relation between the distance between thechord and
13、the arc and the arc radius.1This test method is under the jurisdiction of ASTM Committee D06 on Paperand Paper Products and is the direct responsibility of Subcommittee D06.92 onStandard Documents Relating to Paper and Paper ProductsCurrent edition approved April 1,2007.Published May 2007.Originally
14、approved in 1988.Last previous edition approved in 2002 as D4825 97(2002).DOI:10.1520/D4825-97R07.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document
15、Summary page onthe ASTM website.3Withdrawn.The last approved version of this historical standard is referencedon www.astm.org.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.NOTICE:This standard has either been superseded and replaced by
16、a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest informationDistanceRadius5 mm116.5 cm10 mm58.0 cm15 mm38.6 cm20 mm28.8 cm25 mm22.9 cm30 mm18.9 cm35 mm16.0 cm40 mm13.9 cm5.2 Measuring DeviceA measuring device can be fabri-cated that resembles the letter T.The horizontal member is 216mm(812in.)long.The vertical member is a rule calibrated inmillimetres and mounted so as to be able to slide in the verticalposition.This allows the distance between the end of the rul
