1、Designation:D473710Standard Test Method forCalculated Cetane Index by Four Variable Equation1This standard is issued under the fixed designation D4737;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number
2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 The calculated Cetane Index by Four Variable Equationprovides a means for estimating the ASTM cetane number(Test Method D613)of distillate fuels
3、 from density anddistillation recovery temperature measurements.The valuecomputed from the equation is termed the Calculated CetaneIndex by Four Variable Equation.1.2 The Calculated Cetane Index by Four Variable Equationis not an optional method for expressingASTM cetane number.It is a supplementary
4、 tool for estimating cetane number whena result by Test Method D613 is not available and if cetaneimprover is not used.As a supplementary tool,the CalculatedCetane Index by Four Variable equation must be used with dueregard for its limitations.1.3 Procedure A is to be used for Specification D975,Gra
5、des No.1D S15,No.1D S500,No.1D S5000,No.2DS15,No.2D S5000,and No.4D.This method for estimatingcetane number was developed by Chevron Research Co.2Procedure A is based on a data set including a relatively smallnumber of No.1D fuels.Test Method D4737 Procedure Amay be less applicable to No.1D S15,No.1
6、D S500,and No.1D S5000 than to No.2D grade S5000 or to No.4D fuels.1.3.1 Procedure A has been verified as applicable to GradeNo.2D S15 diesel fuels.31.4 Procedure B is to be used for Specification D975,GradeNo.2D S500.1.5 The test method“Calculated Cetane Index by FourVariable Equation”is particular
7、ly applicable to Grade 1DS5000,Grade No.1D S500,Grade No.2D S5000 and GradeNo.2D S500 diesel fuel oils containing straight-run andcracked stocks,and their blends.It can also be used for heavierfuels with 90%recovery points less than 382C and for fuelscontaining derivatives from oil sands and oil sha
8、le.NOTE1Sxx is the designation for maximum sulfur level specified forthe grade.For example,S500 grades are those with a maximum sulfurlimit of 500 ppm(g/g).1.6 Biodiesel blends are excluded from this test method,because they were not part of the datasets use to develop eitherProcedure A or B.1.7 The
9、 values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.8 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate sa
10、fety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:4D86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD613 Test Method for Cetane Number of Diesel Fuel OilD975 Specification for Diesel
11、Fuel OilsD1298 Test Method for Density,Relative Density,or APIGravity of Crude Petroleum and Liquid Petroleum Prod-ucts by Hydrometer MethodD2887 Test Method for Boiling Range Distribution of Pe-troleum Fractions by Gas ChromatographyD4052 Test Method for Density,Relative Density,and APIGravity of L
12、iquids by Digital Density MeterD6751 Specification for Biodiesel Fuel Blend Stock(B100)for Middle Distillate FuelsD6890 Test Method for Determination of Ignition Delay andDerived Cetane Number(DCN)of Diesel Fuel Oils byCombustion in a Constant Volume ChamberD7170 Test Method for Determination of Der
13、ived Cetane1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.E0 on Burner,Diesel,Non-Aviation Gas Turbine,and MarineFuels.Current edition approved Aug.1,2010.Published September 2010.
14、Originallyapproved in 1987.Last previous edition approved in 2009 as D473709a.DOI:10.1520/D4737-10.2Ingham,M.C.,et al.,“Improved Predictive Equations for Cetane Number,”SAE Paper No 860250,Society of Automotive Engineers(SAE),400 Common-wealth Dr.,Warrendale,PA 15096-0001.3Supporting data(the analys
15、is leading to the use of ProcedureAfor No.2-D S15diesel fuels and to Procedure B)have been filed at ASTM International Headquar-ters and may be obtained by requesting Research Report RR:D02-1699.4For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at ser
16、viceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 Number(DCN)of Diesel Fuel OilsFixed Range Injec-tion Period,Constant Volume Combustion ChamberMethod2.2 CEN Standards:5EN 14214 Automotive fuels Fatty acid methyl esters(FAME)for diesel engines Re
