1、Designation:D505617Standard Test Method forTrace Metals in Petroleum Coke by Atomic Absorption1This standard is issued under the fixed designation D5056;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the analysis for the commonlydetermined trace metals(aluminum,calcium,iron,nickel,silicon,sodium,and vanadium)in labor
3、atory analysis samplesof raw and calcined petroleum coke by atomic absorptionspectroscopy.1.2 The elemental concentration ranges for which this testmethod is applicable and the limits of detection of this testmethod are listed in Table 1.1.3 The values stated in SI units are to be regarded as thesta
4、ndard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For warnings
5、tatements,see Sections 8 10.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organi
6、zation TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D346 Practice for Collection and Preparation of CokeSamples for Laboratory AnalysisD1193 Specification for Reagent WaterD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques t
7、o Evaluate AnalyticalMeasurement System PerformanceD7740 Practice for Optimization,Calibration,and Valida-tion of Atomic Absorption Spectrometry for Metal Analy-sis of Petroleum Products and Lubricants3.Summary of Test Method3.1 A representative sample of the petroleum coke is ashedat 525 C under sp
8、ecified conditions.The ash is fused withlithium tetraborate(Li2B4O7),or lithium metaborate(LiBO3).The melt is dissolved in dilute hydrochloric acid(HCl),and theresultant solution is analyzed by atomic absorption spectros-copy for the following elements:aluminum,calcium,iron,nickel,silicon,sodium,and
9、 vanadium.3.2 Standard practice for using atomic absorption spectrom-etry for determination of metals in petroleum products andlubricants can be found in Practice D7740.4.Significance and Use4.1 The presence and concentration of various metallicelements in a petroleum coke are major factors in the s
10、uitabilityof the coke for various uses.This test method provides a meansof measuring the amounts of those metallic elements in thecoke sample.4.2 The concentration of these elements is one factor indetermining the economic value of the coke.Coke used forproduction of electrodes will have different s
11、pecification re-quirements dependent on what service the electrodes will beused in.Generally the fuel cokes are highest in metallicelement concentration and have the least economic value.4.3 The test method provides a standard procedure for useby the purchaser and seller in the commercial transfer o
12、fpetroleum coke to determine whether the lot of coke meets thespecifications of the purchasing party.5.Interferences5.1 Spectral interferences can occur when using other thanthe recommended wavelength for analysis or when usingmulti-elemental hollow cathode lamps.6.Apparatus6.1 Furnace,electric,capa
13、ble of regulation of temperatureat 525 C 6 10 C.6.2 Magnetic Stirring Hot Plate.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct responsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved May
14、1,2017.Published May 2017.Originallyapproved in 1990.Last previous edition approved in 2015 as D5056 15.DOI:10.1520/D5056-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer
15、 to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with interna
16、tionally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.3 Platinum Dish,50 mL to 58 mL capacity.6.4 Platinum Dish,150 mL to 200 mL capacity.6.5 Platinum-Tipped Tongs.6.6 Furnace,electric,capable of regulation of temperatureat 950 C 6 10 C or a Meker-type forced air burner.6.7 Atomic Absorption Spectrophot
