1、Designation:D516316(Reapproved 2021)Standard Guide forEstablishing a Program for Condition Assessment ofCoating Service Level I Coating Systems in Nuclear PowerPlants1This standard is issued under the fixed designation D5163;the number immediately following the designation indicates the year oforigi
2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard covers procedures for establishing amonitoring program fo
3、r condition assessment of CoatingService Level(CSL)I coating systems in operating nuclearpower plants.Monitoring is an ongoing process of evaluatingthe condition and performance of the in-service coating sys-tems.1.2 It is the intent of this standard to provide a recom-mended basis for establishing
4、a coatings condition assessmentprogram,not to mandate a singular basis for all programs.Variations or simplifications of the program described in thisstandard may be appropriate for each operating nuclear powerplant depending on their licensing commitments.1.3 This requirements of ASME Section XI,In
5、-ServiceInspection Subsections IWE and IWL are beyond the scope ofthis standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practi
6、ces and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and R
7、ecom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D610 Practice for Evaluating Degree of Rusting on PaintedSteel SurfacesD714 Test Method for Evaluating Degree of Blistering ofPaintsD3359 Test Methods for Rating
8、Adhesion by Tape TestD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD4541 Test Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersD5498 Guide for Developing a Training Program for Per-sonnel Performing Coating and Lining Work Inspec
9、tionfor Nuclear FacilitiesD6677 Test Method for Evaluating Adhesion by KnifeD7091 Practice for Nondestructive Measurement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic,Nonconductive Coat-ings Applied to Non-Ferrous MetalsD7108 Guide for Establishing Qualificat
10、ions for a NuclearCoatings SpecialistD7234 Test Method for Pull-Off Adhesion Strength of Coat-ings on Concrete Using Portable Pull-Off Adhesion Tes-ters2.2 SSPC Standards:3SSPC-PA 2 Procedure for Determining Conformance to DryCoating Thickness RequirementsSSPC-PA 9 Measurement of Dry Coating Thickne
11、ss onCementitious Substrates Using Ultrasonic GagesSSPC-VIS 2 Standard Method of Evaluating Degree ofRusting on Painted Steel Surfaces3.Terminology3.1 DefinitionsDefinitions for use with this standard areshown in Terminology D4538 or other applicable standards.3.2 Definitions of Terms Specific to Th
12、is Standard:3.2.1 coating condition assessment,noverall evaluation ofthe coating condition based upon performance monitoring andvisual inspection.1This guide is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsi
13、bility of Subcommittee D33.04 on Quality Systems and Inspection.Current edition approved Feb.1,2021.Published February 2021.Originallyapproved in 1991.Last previous edition approved in 2016 as D5163 16.DOI:10.1520/D5163-16R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta
14、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.Copyright ASTM Inter
15、national,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides
16、 and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2.2 coating maintenance work,nall-inclusive term as-sociated with coating work that expressly relates to repair,refurbishment,or replacement of an existing coating.(See alsocoating work.)3.2.3 in-servicecoatingsmonitoringprogram,nsystematic program established to assess and document thecondition of an existing coating system with respect to pre-scribed performance attributes.4.Significance an
