1、Designation:D522698(Reapproved 2010)1Standard Practice forDissolving Polymer Materials1This standard is issued under the fixed designation D5226;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pa
2、rentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEReapproved with editorial changes throughout in January 2010.1.Scope1.1 This practice outlines the parameters applicable to thepreparation of a polymeric sol
3、ution,such as solvent,concentration,temperature,pressure,time,agitation,and heat-ing mode.1.2 The proper use of this practice requires knowledge ofsolvents and their effect on polymeric materials.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.I
4、t is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating
5、 to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-tics2.2 Other Document:Polymer Handbook33.Terminology3.1 Definitions are in accordance with Terminology D883.3.2 Abbreviations are in accordance with TerminologyD1600.4.Summary of Practice4.1 A polymer solution can be described or p
6、repared usingthe cell classifications listing the parameters relative to solvatethe polymer.The cell classifications are listed in the followingorder:polymer,solvent,concentration,temperature,time,container,heating mode,and agitation.4.1.1 A polymer and a list of suggested solvents for makinga solut
7、ion are listed in Annex A1.4.1.2 Table 1 designates the parameters for container,heat-ing mode,and type of agitation.NOTE2To illustrate the use of the cell classifications with Table 1,a2%solution of poly(vinyl chloride)using cyclohexanone would bewritten as:PVC2 cyclohexanone2 202 662 402 BECwhere:
8、PVC=abbreviation of the polymer from AnnexA1,cyclohexanone=the solvent from Annex A1,20=weight of polymer in tenths of a percent,66=temperature in degrees Celsius,40=time in tenths of an hour,B=glass container from Table 1,E=bath heater from Table 1,andC=random agitation from Table 1.5.Significance
9、and Use5.1 This practice embodies the specifications to describe thepreparation of a polymeric solution.6.Procedure6.1 PolymerSelect the applicable polymer fromAnnexA1and write its abbreviation.6.2 SolventSelect the solvent applicable to the polymerfrom Annex A1.6.3 ConcentrationWrite the polymer gr
10、am weight intenths of a percent per milliliter of solvent.6.4 TemperatureWrite the solution temperature in degreesCelsius.6.5 TimeWrite the time for solution in tenths of an hour.6.6 ContainerSelect the type of container from Table 1.6.7 Heating ModeSelect the heating mode from Table 1.6.8 Agitation
11、Select the agitation mode from Table 1.1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.70 on Analytical Methods.Current edition approved Jan.1,2010.Published February 2010.Originallyapproved in 1992.Last previous edition a
12、pproved in 2003 as D5226-98(2003).DOI:10.1520/D5226-98R101.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Availa
13、ble from John Wiley and Sons,New York,NY.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.Precision and Bias7.1 No statement is made about the precision or bias of thisprac
14、tice since the procedure is descriptive with no measure-ments being made.8.Keywords8.1 polymer solutions;solution preparation;solutions;sol-ventsANNEX(Mandatory Information)A1.SUGGESTED SOLVENTS FOR POLYMERIC SOLUTIONSA1.1 Note the following:A1.1.1 The solvents in Table A1.1 are listed in randomorde
15、r.A1.1.2 An increase in polymer molecular weight reducessolubility.A1.1.3 Branching increases the solubility compared to alinear polymer of the same molecular weight.A1.1.4 Solubility normally increases with rising tempera-ture.A1.1.5 The temperature is for room temperature unlessnoted.A1.1.6 The fo
16、llowing abbreviations are used in Table A1.1:D.S.=degree of substitution,S.C.=substituent content,conc.=concentrated.TABLE A1.1 SolventsAbbreviationPolymerSolventsABAAcrylonitrile-butadiene-acrylatearomatic hydrocarbons,chlorinated hydrocarbons,tetrahydrofuran,esters,ketones,N,N-dimethylformamide,N,N-dimethyl-acetamide(ifhigh acrylonitrile)ABSAcrylonitrile-butadiene-styreneN,N-dimethylformamide,N,N-dimethylacetamide(if high acrylonitrile),cyclohexanone(above 35C),cyclohexanone/acetone,methylcycl
