1、Designation:D429589(Reapproved 2012)Standard Classification forRubber Compounding MaterialsZinc Oxide1This standard is issued under the fixed designation D4295;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This classification system covers the compounding ma-terial commercially known as zinc oxide.The types of zincoxide used in the rubber i
3、ndustry are related to the productionprocess used.Typical chemical and physical properties areincluded.2.Referenced Documents2.1 ASTM Standards:2D280 Test Methods for Hygroscopic Moisture(and OtherMatter Volatile Under the Test Conditions)in PigmentsD3037 Test Method for Carbon BlackSurface Area byN
4、itrogen Adsorption(Withdrawn 1999)3D3280 Test Methods for Analysis of White Zinc PigmentsD4075 Test Methods for Rubber Compounding MaterialsFlame Atomic Absorption AnalysisDetermination ofMetalsD4315 Test Methods for Rubber Compounding MaterialZinc Oxide3.Significance and Use3.1 Zinc oxide is an imp
5、ortant rubber compounding mate-rial.It is used to activate the organic accelerators to increasethe rate of vulcanization and to enhance physical properties.Itis also a vulcanizing agent for halogen-containing elastomers.4.Classification of Zinc Oxides by Types4.1 American Process or Direct TypeWhen
6、zinc oxide ismanufactured by the reduction and reoxidation of a zinc-bearing material,such as a zinc ore by a carbonaceous fuel,itis called American process or direct type.American processzinc oxide is produced with widely varying chemical propertiesand physical characteristics.Nodular-type particle
7、 shape,asobserved by the light microscope,is generally preferred forrubber compounding.Due to wide variations in the materialprocessed and in the process itself,the properties of Americanprocess zinc oxide can only be characterized in a general way.4.2 French Process or Indirect TypeWhen zinc oxide
8、ismanufactured by the burning of zinc vapor(produced byboiling zinc metal in a retort or zinc boiler),it is called Frenchprocess or indirect type.It is characterized by a high degree ofchemical purity resulting from the use of high purity(99.9%zinc).As generally produced,the particles are nodular in
9、 shapeas observed by the light microscope.4.3 Secondary Zinc Oxide Type:4.3.1 ChemicalWhen zinc oxide is manufactured as aby-product of a chemical reaction,it is considered a secondarytype.The chemical and physical properties can vary widelydepending on the raw material source and the type of reacti
10、on.4.3.2 MetallurgicalWhen zinc oxide is manufacturedfrom burning zinc vapor produced by boiling die cast scrapzinc,galvanized zinc dross,or other scrap zinc units withoutpurification,it is considered a secondary type.The chemicalpurity can vary widely and is dependent on the purity of thefeed metal
11、.5.Composition and Properties5.1 Typical properties for untreated zinc oxide by types aredescribed in Table 1.5.2 Treated Zinc OxideZinc oxide for use in rubber isoften surface treated,most frequently with a fatty acid such aspropionic acid.5.2.1 A fatty acid treated zinc oxide will typically contai
12、nabout 0.5%less zinc oxide than the corresponding untreatedgrade.5.2.2 The typical fatty acid treated zinc oxide shows agreater heat loss,about 0.2%,than the corresponding untreatedgrade due to partial vaporization of the fatty acid.1This classification is under the jurisdiction of ASTM Committee D1
13、1 onRubber and is the direct responsibility of Subcommittee D11.20 on CompoundingMaterials and Procedures.Current edition approved May 1,2012.Published June 2012.Originallyapproved in 1983.Last previous edition approved in 2005 as D4295 89(2005).DOI:10.1520/D4295-89R12.2For referenced ASTM standards
14、,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright AS
15、TM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determi
16、nation of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful considerati
