1、Designation:D433901(Reapproved 2018)Standard Test Method forDetermination of the Odor of Adhesives1This standard is issued under the fixed designation D4339;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method describes a procedure for evaluatingt
3、he odor of adhesives.It is intended to replace FederalStandard 175A,Method 4051.1.2 This test method provides a means of comparing theodor of an adhesive sample to a reference sample.It is notintended to give an absolute value for the odor of a sample.Itcan be used for wet or dry samples.1.3 Warning
4、Do not use this test method with adhesivescontaining hazardous components such as solvent residues andunreacted monomeric materials.1.4 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.5 This standard does not purport t
5、o address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.See 1.3 for specific precautionary state
6、ments.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarrie
7、rs to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D907 Terminology of AdhesivesD1391 Method for Measurement of Odor in Atmospheres(Dilution Method)(Withdrawn 1986)33.Terminology3.1 DefinitionsSeveral terms in this test method are de-fined in accordance with Terminology D907.3.2 Def
8、initions of Terms Specific to This Standard:3.2.1 odor,nthat property of a substance which affects thesense of smell.4.Significance and Use4.1 The results from this determination are useful in deter-mining the suitability of adhesives in applications where theodor level associated with the end use i
9、s critical.5.Apparatus5.1 Glass Bottles,1-qt(1-L),wide-mouth,straight sided,with screw caps.NOTE1It is important that the bottles and caps be kept clean andodor-free.Discard any bottle which cannot be made visibly clean orodor-free.Wash bottles and caps with a suitable cleaning powder,rinsethoroughl
10、y with tap water,then rinse with distilled water,drain,and dryin an oven.Do all cleaning in an odor-free atmosphere.5.2 Oven or Incubator,for aging samples at elevated tem-peratures.5.3 Aluminum Foil.5.4 Balance,capable of measuring to nearest 0.1 g.6.Test Sample and Test Specimen6.1 Select a test s
11、ample representative of the adhesive beingtested.It may be liquid or solid.Keep in a tightly closedcontainer until used(5.1).6.2 For the test specimen,place 20.0 6 0.1 g of the testsample into the glass bottle(5.1),cover with aluminum foil,place the cap on the bottle and tighten.NOTE2Always use new
12、aluminum foil,never reuse it.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.10 on WorkingProperties.Current edition approved Nov.1,2018.Published November 2018.Originallyapproved in 1984.Last previous edition approve
13、d in 2013 as D4339 01(2013).DOI:10.1520/D4339-01R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last appr
14、oved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization esta
15、blished in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 7.Reference Sample and Reference Specimen7.1 Select a reference sample,that from prior experience orknowle
16、dge,or by agreement between supplier and purchaser ofadhesive,has acceptable odor.7.1.1 Store the reference sample in a tightly closedcontainer,specified in 5.1,in a reasonably odor-free atmo-sphere.7.1.2 Take care against contamination of the referencesample.If it is suspected that the reference sample has beencontaminated,discard it and obtain a new reference sample.7.2 For the reference specimen,transfer 20.0 6 0.1 g of thereference sample into the glass bottle(5.1),cover with alumi-num foil,
