收藏 分享(赏)

ASTM_D_3807_-_98_2019.pdf

上传人:益****师 文档编号:178340 上传时间:2023-03-04 格式:PDF 页数:3 大小:102.70KB
下载 相关 举报
ASTM_D_3807_-_98_2019.pdf_第1页
第1页 / 共3页
ASTM_D_3807_-_98_2019.pdf_第2页
第2页 / 共3页
ASTM_D_3807_-_98_2019.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D380798(Reapproved 2019)Standard Test Method forStrength Properties of Adhesives in Cleavage Peel byTension Loading(Engineering Plastics-to-EngineeringPlastics)1This standard is issued under the fixed designation D3807;the number immediately following the designation indicates the year o

2、foriginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the com-parative cle

3、avage/peel strengths of adhesives for bondingengineering plastics when tested on a standard specimen andunder specific conditions of preparation and testing.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard d

4、oes not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international

5、standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.R

6、eferenced Documents2.1 ASTM Standards:2D907 Terminology of Adhesives3.Terminology3.1 DefinitionsMany of the terms used in this test methodare defined in Terminology D907.3.2 Definitions of Terms Specific to This Standard:3.2.1 semirigid adherend,nan adherend that has dimen-sions and physical propert

7、ies that permit bending at designatedtest temperature through any angle up to 30 without breakingor cracking.4.Significance and Use4.1 This test method determines strength properties ofadhesives in cleavage peel by tension loading.It allows thecomparative testing of cleavage/peel strengths of bonded

8、engineering thermoplastic adherends.4.2 Cleavage/peel forces are common in bonded assemblies.This test method gives information as to the performance ofsubstrate/adhesive combinations under cleavage/peel forces.5.Apparatus5.1 Tension Testing Machine,capable of applying a tensileload having the follo

9、wing prescribed conditions:5.1.1 Select the machine and loading range so that themaximum load on the specimen falls between 15 and 85%ofthe upper limit of the loading range.5.1.2 Maintain the rate of movement between heads to beessentially constant under fluctuating loads.NOTE1It is difficult to mee

10、t this requirement when loads aremeasured with a spring-type or pendulum-type weighing device.Gear-driven head separation is recommended.5.1.3 Equip the machine with suitable grips capable ofclamping the specimens firmly throughout the tests.5.1.4 The machine is autographic,giving a chart that can b

11、eread in terms of centimetres(inches)of separation as onecoordinate and applied load as the other coordinate.5.1.5 The applied tension as measured and recorded is to beaccurate within 61%.5.2 Conditioning Room or Desiccators,capable of main-taining a relative humidity of 50 6 5%at 23 6 2C.6.Test Spe

12、cimen6.1 Laminated test panels(see Fig.1)consist of twosemirigid adherends properly prepared and bonded together inaccordance with the manufacturers recommendations.Spe-cially prepared test specimens shall be 25.4 mm(1 in.)wide by1This test method is under the jurisdiction of ASTM Committee D14 onAd

13、hesives and is the direct responsibility of Subcommittee D14.40 on Adhesives forPlastics.Current edition approved June 1,2019.Published June 2019.Originallyapproved in 1979.Last previous edition approved in 2012 as D3807 98(2012).DOI:10.1520/D3807-98R19.2For referenced ASTM standards,visit the ASTM

14、website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis

15、 international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)

16、Committee.1 177.3 mm(7 in.)long,but bonded only over approximately 76mm(3 in.)of their length.Test specimens of these samedimensions may also be cut from larger,fully laminated panels.6.1.1 Direct comparisons of different adhesives are madeonly when specimen construction and test conditions areidentical.NOTE2General purpose ABS(acrylonitrile-butadiene-styrene)molded plaques approximately 6.3 mm(0.25 in.)thick have been foundsatisfactory as adherends for structural adhesives.Other engineeringplas

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2