1、Designation:D3889/D3889M96(Reapproved 2012)Standard Test Method forAdherence to Linerboard of Pressure-Sensitive Tape at LowTemperature1This standard is issued under the fixed designation D3889/D3889M;the number immediately following the designation indicates theyear of original adoption or,in the c
2、ase of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This test meth
3、od covers one procedure for determiningthe adherence of pressure-sensitive tapes to a standard lin-erboard or other similar surface.1.2 This test method provides for an attribute response(passor fail)and does not yield numerical data on a variable orcontinuous scale.1.3 The values stated in either S
4、I or inch-pound units are tobe regarded separately as standard.The values stated in eachsystem may not be exact equivalents;therefore,each systemmust be used independently without combining values in anyway.1.4 This standard does not purport to address all of thesafety concerns,if any,associated wit
5、h its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Environ-mentsD3715/D37
6、15M Practice for Quality Assurance of Pressure-Sensitive TapesD4332 Practice for Conditioning Containers,Packages,orPackaging Components for TestingE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or Process3.Terminology3.1 Defini
7、tionsGeneral terms in this test method are de-fined in Terminology D996.4.Summary of Test Method4.1 The pressure-sensitive tape to be tested is adhered to thestandard linerboard or other material of interest.Following adwell period at an elevated temperature,the specimen assem-bly is cooled to a spe
8、cific temperature.After a specified time atthe low temperature the specimen assembly is flexed around asmall mandrel and observed for indications of bond failure.5.Significance and Use5.1 Satisfactory tape performance at the test temperatureimplies satisfactory cold-temperature performance at or abo
9、vethe test temperature.5.2 This procedure would be applicable for questions ofadherence to 100%kraft fiberboards similar to the standardlinerboard surface without substitution but for direct informa-tion on any board or surface,the actual surface in questionshould be substituted.6.Apparatus6.1 Stand
10、ard Reference Material 1810A,3length approxi-mately 280 mm 11 in.,width approximately 13 mm 12in.wider than the specimen width.See Section 8.NOTE1When agreed upon between the parties involved or whencalled for by the material specification,other flexible material may besubstituted for the 1810 liner
11、board.6.2 Rubber-Covered Steel Roller,482.5 6 1.3 mm 3.25 60.1 in.in diameter and 44.5 6 1.3 mm 1.75 6 0.05 in.wide,covered with rubber approximately 6 mm 0.25 in.thick1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.1
12、4 on Tape andLabels.Current edition approved April 1,2012.Published May 2012.Originallyapproved in 1980.Last previous edition approved in 2006 as D3889/D3889M 96(2006).DOI:10.1520/D3889_D3889M-96R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at
13、 serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Standard Reference Material 1810A is available from the U.S.GovernmentPrinting Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 204
14、01,http:/www.access.gpo.gov.4The sole source of supply of the apparatus known to the committee at this timeis Chemsultants International,9349 Hamilton Dr.,Mentor,OH 440611118.If youare aware of alternative suppliers,please provide this information to ASTMInternational Headquarters.Your comments will
15、 receive careful consideration at ameeting of the responsible technical committee,1which you may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 having a Shore A durometer hardness of 80 6 5.The surfaceof the rubber shall form a tr
16、ue cylinder devoid of any convexor concave deviations.The mass of the roller shall be 2040 645 g 4.5 6 0.1 lb.The mass of the handle shall not add to themass of the roller during use.6.3 Oven,air circulating,maintained at 66 6 1C 150 62F.6.4 Cold Chamber,maintained at a specified tempera-ture 54 6 1C 65 6 2F if no other temperature isspecified.6.5 Nonrotating,Smooth Surface,Metal Cylinder,having adiameter of 40 6 6 mm 1.5 6 0.25 in.and minimum lengthof 50 mm 2 in.fixed to a base or support for u
