收藏 分享(赏)

ASTM_D_3912_-_10_2017.pdf

上传人:益****师 文档编号:178373 上传时间:2023-03-04 格式:PDF 页数:2 大小:62.90KB
下载 相关 举报
ASTM_D_3912_-_10_2017.pdf_第1页
第1页 / 共2页
ASTM_D_3912_-_10_2017.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D391210(Reapproved 2017)Standard Test Method forChemical Resistance of Coatings and Linings for Use inNuclear Power Plants1This standard is issued under the fixed designation D3912;the number immediately following the designation indicates the year oforiginal adoption or,in the case of r

2、evision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method establishes procedures for the evalua-tion of the chemical resistance of coatings and

3、linings for usein Coating Service Level I and II applications in nuclear powerplants.1.2 This test method is intended to be used as a screeningtest to evaluate coatings and linings on steel and concretesubstrates.1.3 This test method addresses two exposure intervals:(1)Short Term(Typically 5 days):S

4、uch exposures areprimarily applicable for coatings exposed to chemical splash orspill.(2)Long Term(Typically 180 days):Such exposures areprimarily applicable for linings exposed to continuous ornear-continuous chemical immersion.1.4 The values stated in inch-pound units are to be regardedas standard

5、.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard t

6、o establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Princi

7、ples for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D714 Test Method for Evaluating Degree of Blistering ofPaintsD1193 Specification for Reagent WaterD

8、5139 Specification for Sample Preparation for Qualifica-tion Testing of Coatings to be Used in Nuclear PowerPlantsD7230 Guide for Evaluating Polymeric Lining Systems forWater Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates2.2 NACE Standard:NACE Standard TM-01-7

9、42002 Laboratory Methods forthe Evaluation of Protective Coatings Used as LiningMaterials in Immersion Service33.Significance and Use3.1 The lining test described in 6.2 may be used to evaluatethe chemical resistance characteristics of coating systems forlining surfaces of tanks,vessels and similar

10、facilities used inCoating Service Level I and II applications in a nuclear powerplant.For the evaluation of linings in Coating Service Level IIIwater immersion applications in nuclear power plants use thetest methods and guidance found in Guide D7230.3.2 The specific chemical resistance tests descri

11、bed in 6.1are dependent upon the relative severity of the service condi-tions.The specific chemical reagents to be used shall bespecified to reflect the intended service conditions.3.3 At the discretion of the user,the methods presented mayalso be used to evaluate coatings and linings for applicatio

12、ns inother types of power plants or other industrial services.1This test method is under the jurisdiction of ASTM Committee D33 onProtective Coating and Lining Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.02 on Service and Material Parameters.Current editi

13、on approved Sept.1,2017.Published September 2017.Originallyapproved in 1980.Last previous edition approved in 2010 as D3912 10.DOI:10.1520/D3912-10R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandard

14、s volume information,refer to the standards Document Summary page onthe ASTM website.3Available from NACE International(NACE),15835 Park Ten Pl.,Houston,TX77084,http:/www.nace.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis interna

15、tional standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committe

16、e.1 4.Sampling4.1 Prepare individual specimens for testing.4.2 Prepare one additional specimen as a control.Multipletests may be performed.5.Preparation of Test Specimens5.1 Steel Panels:5.1.1 Prepare steel panels in accordance with SpecificationD5139.5.2 Concrete BlocksPrepare blocks in accordance withSpecification D5139 with the exception that the top and bottomends of the block shall be coated.6.Procedure6.1 Short Term Tests:6.1.1 Test the chemical resistance properties of the coatingsby imme

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2