1、Designation:D359702(Reapproved 2018)1Standard Performance Specification forWoven Upholstery FabricsPlain,Tufted,or Flocked1This standard is issued under the fixed designation D3597;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made throughout in December 2018.1.Scope1.1 This performance specification covers the performancer
3、equirements for plain,tufted,or flocked woven upholsteryfabrics as used in the manufacture of new indoor furniture.These requirements apply to both the warp and filling direc-tions for those factors where each fabric direction is pertinent.1.2 This performance specification is not applicable tofabri
4、cs used in porch,deck,or lawn furniture;nor for knittedfabrics,bonded or laminated fabrics,or surface-coated fabrics(such as vinyls and urethanes).1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are
5、provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine
6、the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations iss
7、ued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1424 Test Method for Tearing Strength
8、 of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2262 Test Method for Tearing Strength of Woven Fabricsby the Tongue(Single Rip)Method(Constant-Rate-of-Traverse Tensile Testing Machine)(Withdrawn 1995)3D4157 Test Method for Abrasion Resistance of TextileFabrics(Oscillatory Cylinder Method)D50
9、34 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)2.2 AATCC Test Methods:4Test Method 8 AATCC Colorfastness to Crocking:Crockmeter MethodTest Method 16.3 Colorfastness to Light:Xenon ArcTest Method 23 Colorfastness to Burnt Gas FumesTest Method 107 Colorfastness to Wate
10、rTest Method 116 Colorfastness to Crocking:Rotary VerticalCrockmeter MethodTest Method 129 Colorfastness to Ozone in the AtmosphereUnder High HumiditiesEvaluation Procedure 1 Gray Scale for Color ChangeEvaluation Procedure 8 AATCC 9-Step Chromatic Transfer-ence Scale2.3 Federal Standard:16CFR,Chapte
11、r II-Consumer Product Safety Commission,Subchapter D-Flammable Fabrics Act Regulation52.4 Military Standard:ASQ/ANSI Z1.4 Sampling Procedures and Tables for In-spection by Attributes61This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textilesand is the direct responsib
12、ility of Subcommittee D13.63 on HomeFurnishings.Current edition approved Dec.15,2018.Published January 2019.Originallyapproved in 1977.Last previous edition approved in 2013 as D3597 02(2013).DOI:10.1520/D3597-02R18E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM
13、 Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4AATCC Technical Manual,available from American Association of
14、TextileChemists and Colorists(AATCC),P.O.Box 12215,Research Triangle Park,NC27709,http:/www.aatcc.org.5Available from Superintendent of Documents,U.S.Government PrintingOffice,Washington,DC 20402.6Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19
15、111-5094,Attn:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevel
16、opment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.5 Non-Governmnet Organization Standard:Specifications Standards Test Procedures for UpholsteredFurniture Fabrics7Guides for the Household Furniture Industry8NOTE1Reference to documents in this standard give only thepermanent part of the designation of ASTM,AATCC,or other testmethods and standards.The current editions of each test method citedshall prev
