1、Designation:D 3743 84(Reapproved 2000)Standard Terminology Relating toBridge Deck and Substructure Protection1This standard is issued under the fixed designation D 3743;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、 revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.ScopeThis standard defines terminology commonly used in thediscussion of bridge deck protective systems and waterproofingmembranes.2.Te
3、rminologyabrasive blast cleaningthe removal from a concrete surfaceof all laitance,oil,grease,curing compounds,or coatings bythe action of a high-velocity stream of abrasive in air orwater followed by a blast of air to provide a concrete surfacefree of abrasive dust and other particles.The abrasive
4、maybe clean silica sand,mineral grit,steel shot,steel grit,ormineral slag.anodes,impressed currentinactive materials such as high-silicon cast iron and graphite.These anodes provide theelectrical connection to the conductive overlay,but requireuse of an outside source for protective energy,that is,a
5、nimpressed current.At the current densities recommended bythe manufacturers,these anodes are highly resistant toelectrolytic attack but deteriorate at known rates.anodes,sacrificialchemically active metals such as zinc,aluminum,and magnesium which,when electrically con-nected to the reinforcing bar,
6、will provide the energy neededto cathodically protect the reinforcing bar.Sacrificial anodesdeteriorate in service at a rate proportional to the energyneeded to protect the reinforcing bar plus whatever maydeteriorate by local-action corrosion.bitumen,polymer-modifieda black or dark-colored cemen-ti
7、tious,high-molecular weight hydrocarbon such as asphalt,tar,or pitch in which polymer has been dispersed to modifythe properties of the bitumen.bitumen,rubberizeda special form of polymer-modifiedbitumen where an asphalt,tar,or pitch has been combinedwith natural or synthetic rubber to modify its pr
8、operties.bleedersholes or pipes through bridge decks to provide fordrainage.blistersgas-or water vapor-filled bubbles or cavities in thewaterproofing membrane caused by entrapped air,the vola-tilization of liquids applied to the concrete,or the vaporiza-tion of water on or in the concrete.cathodic p
9、rotectionthe control of corrosion by the applica-tion of a cathodic current to the reinforcing steel by means ofimpressed current or a sacrificial anode.conductive bituminous overlaya first course bituminousoverlay using aggregate or high-crystalline structure carbon,or equivalent,which is capable o
10、f distributing impressedcurrent from the anodes to all parts of the bridge deckroadway surface.conductive polymer mortara rigid material formulated bypolymerization of a select resin system and conductivecalcined petroleum coke which is capable of distributingimpressed anodic current.The material is
11、 used to fill cutslots,as strips or ribbons in grid-fashion on a bridge deck orstructure,or applied as a thin overlay to substructureconcrete members for stopping the corrosion of reinforcingsteel.continuous spun bonded polypropylene mat a sheet ma-terial,resembling paper or felt,made from polypropy
12、leneplastic fibers,used in the manufacture of preformed mem-brane sheet for waterproofing.curingthe development of hardness,strength,or other de-sired properties by evaporation,polymerization,or chemicaland physical change in a material that is initially liquid orplastic in consistency.curing agenta
13、nything such as heat,a catalyst,or a protectivecoating that assures,enhances,or accelerates curing.half cella standard reference electrode used to measure theelectrical potential between it and the reinforcing steel.Mostcommonly used on bridge decks is the saturated copper-copper sulfate half cell(C
14、SE).impregnationfilling the void structure of hardened concreteby saturating it with a liquid system.impressed current protectionapplication of cathodic pro-tection by means of an external dc power source.latex-modified portland cement concrete concrete thatincludes polymer emulsion,resulting in a d
15、ense hardenedconcrete resisting the movement of moisture and chlorideions.Usually used as a relatively thin overlay(1 to 112in.(25 to 38 mm)on conventional concrete bridge decks.1These definitions are under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and are the direct respons
16、ibility of Subcommittee D04.32 onBridges and Structures.Current edition approved Sept.28,1984.Published November 1984.Originallypublished as D 3743 79.Last previous edition D 3743 79.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.NOTICE:This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest informationmastica thick adhesive material used as a cementin
