收藏 分享(赏)

ASTM_D_2996_-_15.pdf

上传人:益****师 文档编号:178947 上传时间:2023-03-04 格式:PDF 页数:6 大小:98.02KB
下载 相关 举报
ASTM_D_2996_-_15.pdf_第1页
第1页 / 共6页
ASTM_D_2996_-_15.pdf_第2页
第2页 / 共6页
ASTM_D_2996_-_15.pdf_第3页
第3页 / 共6页
ASTM_D_2996_-_15.pdf_第4页
第4页 / 共6页
ASTM_D_2996_-_15.pdf_第5页
第5页 / 共6页
ASTM_D_2996_-_15.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D299615An American National StandardStandard Specification forFilament-Wound“Fiberglass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe1This standard is issued under the fixed designation D2996;the number immediately following the designation indicates the year oforiginal adoption or,in

2、the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers machine-made reinforced ther-mosetting resin pressure pipe(RTRP

3、)manufactured by thefilament winding process up to 60 in.nominal size.Includedare a classification system and requirements for materials,mechanical properties,dimensions,performance,methods oftest,and marking.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in

4、 parentheses are provided forinformation purposes only.1.3 The following safety hazards caveat pertains only to thetest method portion,Section 8,of this specification:Thisstandard does not purport to address all of the safety problems,if any,associated with its use.It is the responsibility of the us

5、erof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE1The term“fiberglass pipe”as described in Section 3 of thisspecification applies to both reinforced thermosetting resin pipe(RTRP)and reinforced polymer

6、mortar pipe(RPMP).This specification coversonly reinforced thermosetting resin pipe(RTRP).NOTE2This specification is applicable to RTRP where the ratio ofoutside diameter to wall thickness is 10:1 or more.NOTE3There is no known ISO equivalent to this standard.NOTE4For the purposes of this standard,p

7、olymer does not includenatural polymers.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD883 Terminology Relating to PlasticsD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal Pr

8、essureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2105 Test Method for Longitudinal Tensile Properties of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)Pipe and TubeD2143 Tes

9、t Method for Cyclic Pressure Strength ofReinforced,Thermosetting Plastic PipeD2310 Classification for Machine-Made“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2992 Practice

10、 for Obtaining Hydrostatic or Pressure De-sign Basis for“Fiberglass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe and FittingsD3567 Practice for Determining Dimensions of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)Pipe andFittingsF412 Terminology Relating to Plastic Piping Systems3.Ter

11、minology3.1 Definitions:3.1.1 GeneralDefinitions are in accordance with Termi-nologies D883 and F412 and abbreviations are in accordancewith Terminology D1600,unless otherwise indicated.Theabbreviation for reinforced thermosetting resin pipe is RTRP.3.2 Definitions of Terms Specific to This Standard

12、:3.2.1 coatinga resin layer,with or without filler orreinforcement,or both,applied to the exterior surface of thepipe structural wall.3.2.2 fiberglass pipea tubular product containing glass-fiber reinforcements embedded in or surrounded by curedthermosetting resin;the composite structure may contain

13、aggregate,granular or platelet fillers,thixotropic agents,pigments,or dyes;thermoplastic or thermosetting liners orcoatings may be included.3.2.3 filament windinga process used to manufacture tu-bular goods by winding continuous fibrous glass strand roving,or roving tape,saturated with liquid resin

14、or preimpregnatedwith partially cured resin(subsequent heating may be required1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved May

15、 1,2015.Published June 2015.Originallyapproved in 1971.Last previous edition approved in 2007 as D2996 01(2007)1.DOI:10.1520/D2996-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informat

16、ion,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 to polymerize the resin system)onto the outside of a mandrelin a predetermined pattern under controlled tension;the insidediameter(ID)of the pipe is fixed by the mandrel outsidediameter and the outside diameter(OD)of the pipe is deter-mined by the amount of

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2