1、Designation:D404718Designation:149/93Standard Test Method forPhosphorus in Lubricating Oils and Additives by QuinolinePhosphomolybdate Method1This standard is issued under the fixed designation D4047;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test
3、method covers the determination of 0.005%to10.0%by mass phosphorus in unused lubricating oil andadditive concentrates.There is no reason to doubt its applica-bility to filtered,used lubricating oils,but no systematic studyof this application has been made.1.2 The test method is applicable to samples
4、 containing anyof the phosphorus compounds in normal use.NOTE1This test method extends the scope of the previous version ofIP 149 and replaces IP 148 and the previous version of IP 149 as a refereemethod.1.3 This test method is free from most interferences becausethe high insolubility of the quinoli
5、ne phosphomolybdate pre-cipitate leads to constant composition and freedom from mostadsorbed or occluded impurities,especially from cations whichwould otherwise interfere in the subsequent titration of theprecipitate.1.4 Barium,calcium,magnesium,zinc,iron,aluminum,alkali salts,citric acid and citrat
6、es,chromium up to 18 timesthe phosphorus content,and titanium up to 3.5 times do notinterfere with the test method.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety
7、 concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statements,see 6.9.1.7 This international stan
8、dard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Refer
9、enced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Technique
10、s to Evaluate AnalyticalMeasurement System Performance2.2 IP Standard:IP 148 Test Method for Phosphorous in Lubricating Oilsand Additives33.Summary of Test Method3.1 Additive concentrates are diluted with phosphorus-freewhite oil to produce a working blend.3.2 The sample is ignited with excess of zi
11、nc oxide wherebyphosphorus is converted to phosphate.The residue is dissolvedin hydrochloric acid and any sulfide formed is oxidized withpotassium bromate.Phosphorus is then precipitated as quino-line phosphomolybdate and determined volumetrically byaddition of excess standard alkali and back titrat
12、ion withstandard acid.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved April 1,2018.Published April 2018.Originallyapproved in 1981.
13、Last previous edition approved in 2013 as D4047 13.DOI:10.1520/D4047-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM we
14、bsite.3Available from Energy Institute,61 New Cavendish St.,London,W1G 7AR,U.K.,http:/www.energyinst.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international sta
15、ndard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.Sign
16、ificance and Use4.1 Knowledge of the phosphorus content,and thus thephosphorus-containing additives,in a lubricating oil or addi-tive can be used to predict performance characteristics.5.Apparatus5.1 Silica Crucibles,40 mm internal diameter at the top and40 mm in height.The internal surface should be smooth andfree from pitting.5.2 Muffle Furnace,capable of maintaining a temperature ofapproximately 700 C,and fitted with ports to allow aircirculation.5.3 Beakers,25 mL capacity.5.4 Filtering Appar
