收藏 分享(赏)

ASTM_D_3335_-_85a_2020.pdf

上传人:益****师 文档编号:179183 上传时间:2023-03-04 格式:PDF 页数:4 大小:86.88KB
下载 相关 举报
ASTM_D_3335_-_85a_2020.pdf_第1页
第1页 / 共4页
ASTM_D_3335_-_85a_2020.pdf_第2页
第2页 / 共4页
ASTM_D_3335_-_85a_2020.pdf_第3页
第3页 / 共4页
ASTM_D_3335_-_85a_2020.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D333585a(Reapproved 2020)Standard Test Method forLow Concentrations of Lead,Cadmium,and Cobalt in Paintby Atomic Absorption Spectroscopy1This standard is issued under the fixed designation D3335;the number immediately following the designation indicates the year oforiginal adoption or,in

2、 the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This

3、 test method covers the determination of lead2contents between 0.01 and 5%,cadmium contents between 50and 150 ppm(mg/kg),and cobalt contents between 50 and2000 ppm(mg/kg)present in the nonvolatile portion of liquidcoatings or contained in dried films.There is no reason tobelieve that higher levels o

4、f all three elements could not bedetermined by this test method,provided that appropriatedilutions and adjustments in specimen size and reagent quan-tities are made.1.2 Only pigmented coatings were used for evaluating thistest method,but there is no reason to believe that varnishes andlacquers could

5、 not be analyzed successfully,provided thatappropriate precautions are taken.1.3 This test method is not applicable to the determinationof lead in samples containing antimony pigments(low recov-eries are obtained).1.4 If lead is present in the sample to be analyzed in theform of an organic lead comp

6、ound at a concentration greaterthan 0.1%,small losses of lead may occur,resulting in slightlypoorer precision than shown in Section 12.1.5 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.6 This standard does not purport to add

7、ress all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific hazard statements are given in Secti

8、on 7.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarrier

9、s to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D1193 Specification for Reagent WaterD2832 Guide for Determining Volatile and Nonvolatile Con-tent of Paint and Related Coatings3.Summary of Test Method3.1 The specimen of liquid coating or dried film is preparedfor analysis by dry a

10、shing.The content of lead,cadmium,orcobalt of an acid extract of the ash is determined by atomicabsorption spectroscopy.4.Significance and Use4.1 The permissible level of heavy metals in certain coat-ings is specified by governmental regulatory agencies.This testmethod provides a fully documented pr

11、ocedure for determininglow concentrations of lead,cadmium,and cobalt present inboth water and solvent-reducible coatings to determine com-pliance.5.Apparatus5.1 Atomic Absorption Spectrophotometer,consisting of anatomizer and either a single-or three-slot burner;gas pressureregulating and metering d

12、evices for air and acetylene;lead,cadmium,and cobalt source lamps4with a regulated constant-current supply;a monochromator and associated optics;aphotosensitive detector connected to an electronic amplifier;and a readout device.1This test method is under the jurisdiction of ASTM Committee D01 on Pai

13、ntand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved Feb.1,2020.Published February 2020.Originallyapproved in 1974.Last previous edition approved in 2014 as D3335 85a(2014)

14、.DOI:10.1520/D3335-85AR20.2Vandeberg,J.T.,Swafford,H.D.,and Scott,R.W.,“Determination of LowConcentrations of Lead in Paint,”Journal of Paint Technology,Vol 47,No.604,May 1975.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For An

15、nual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Both hollow cathode lamps and electrodeless discharge lamps have been foundsatisfactory for this purpose.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA

16、19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.5.2 Muffle Furnace,capable of maintaining 500 6 10C.5.3 Crucibles,wide-form,porcelain,glazed inside and out-side except for the outside bottom surface,approximate

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2