收藏 分享(赏)

ASTM_D_2978_-_15.pdf

上传人:益****师 文档编号:179339 上传时间:2023-03-04 格式:PDF 页数:3 大小:64.26KB
下载 相关 举报
ASTM_D_2978_-_15.pdf_第1页
第1页 / 共3页
ASTM_D_2978_-_15.pdf_第2页
第2页 / 共3页
ASTM_D_2978_-_15.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D297815Standard Test Methods forVolume of Processed Peat Materials1This standard is issued under the fixed designation D2978;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenthese

2、s indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 These test methods cover the measurement of thevolume of loose and baled processed peat expressed as cubicfeet and is used as a quality control measurement to

3、 determineif the package contains the labeled amount of material.Theresults of these test methods are highly dependent on theexperience of the personnel running the procedure.1.2 There are two test methods,Method A for Loose Peatand Method B for Baled Peat.Method A is used when thematerial is uncomp

4、acted and Method B is used when thematerial is compacted.1.3 UnitsThe values stated in inch-pound units are to beregarded as standard.Except,that the sieve designations aretypically identified using the“alternative”system in accor-dance with Practice E11,such as 3-in.and No.200,instead ofthe“standar

5、d”of 75-mm and 75-m,respectively.1.4 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026.1.4.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as theindustry stan

6、dard.In addition,they are representative of thesignificant digits that generally should be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or re

7、duce significant digits of reported data to becommensurate with these considerations.It is beyond the scopeof this standard to consider significant digits used in analysismethods for engineering design.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its

8、 use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD3740 Practice f

9、or Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD6026 Practice for Using Significant Digits in GeotechnicalDataE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3.Terminology3.1 Definitions:3.1.1 For

10、 definitions of common technical terms in thisstandard,refer to Terminology D653.3.2 Definitions of Terms Specific to This Standard:3.2.1 loose peat,nuncompacted peat in air-dried,granu-lated or crumb form.4.Summary of Test Method4.1 These test methods consist of either measuring the outerdimensions

11、 of compacted peat(Method B)or dividing theparticles of uncompacted peat(Method A)by passing themthrough a12-in.(12.5-mm)sieve and allowing them to fall intoa volume-measuring container.5.Significance and Use5.1 These test methods are used to quantify the volume ofpeats under consideration in commer

12、cial transactions to deter-mine if the package contains the labeled quantity.As such,material comes into the test area in an“as sold”condition.NOTE1The quality of the result produced by this standard isdependent on the competence of the personnel performing it,and thesuitability of the equipment and

13、 facilities used.Agencies that meet thecriteria of Practice D3740 are generally considered capable of competentand objective testing/sampling/inspection/etc.Users of this standard arecautioned that compliance with Practice D3740 does not in itself ensurereliable results.Reliable results depend on ma

14、ny factors;Practice D37401This test method is under the jurisdiction ofASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.22 on Soil as a Mediumfor Plant Growth.Current edition approved May 1,2015.Published June 2015.Originallyapproved in 1971.Last previous editi

15、on approved in 2010 as D2978 03(2010).DOI:10.1520/D2978-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summ

16、ary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 provides a means of evaluating some of those factors.6.Apparatus6.1 Sieve,12-in.(12.5-mm),conforming to SpecificationE11.6.2 Measuring ContainerAsteel or wood bound containerwith metal having one of the following sets of inside dimen-sions:Size(ft3)Measuring Container Dimensions(W L H)1212 12 12 in.with line scribed at6 in.from th

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2