收藏 分享(赏)

ASTM_D_3159_-_15.pdf

上传人:益****师 文档编号:179571 上传时间:2023-03-04 格式:PDF 页数:5 大小:146.07KB
下载 相关 举报
ASTM_D_3159_-_15.pdf_第1页
第1页 / 共5页
ASTM_D_3159_-_15.pdf_第2页
第2页 / 共5页
ASTM_D_3159_-_15.pdf_第3页
第3页 / 共5页
ASTM_D_3159_-_15.pdf_第4页
第4页 / 共5页
ASTM_D_3159_-_15.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D315915Standard Specification forModified ETFE Fluoropolymer Molding and ExtrusionMaterials1This standard is issued under the fixed designation D3159;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisi

2、on.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers molding and extrusion

3、mate-rials of modified ETFE fluoropolymer.The ETFE resin is acopolymer of ethylene and tetrafluoroethylene.Modified ETFEresin contains no more than 5 mole%of other fluoromono-mers.1.2 The values stated in SI units as detailed in IEEE/ASTMSI-10 are to be regarded as standard.The values given inparent

4、heses are for information only.NOTE1Although this specification and ISO 12086-1 and ISO12086-2 differ in approach or detail,data obtained using either aretechnically equivalent.1.3 The following safety hazards caveat pertains only to thetest method portion,Section 11,of this specification.Thisstanda

5、rd does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.1.4 Recycled material is not appro

6、priate for this specifica-tion because performance requirements cannot be met withrecycled material.Therefore,this specification is for virginmaterial only.2.Referenced Documents2.1 ASTM Standards:2D150 Test Methods for AC Loss Characteristics and Permit-tivity(Dielectric Constant)of Solid Electrica

7、l InsulationD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD1238 Test Method for Melt Flow Rates of Thermoplasti

8、csby Extrusion PlastometerD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3418 Test Method for Transition Temperatures and En-thalpies of Fusion and Crystallization of Polymers byDifferential Scanning CalorimetryD3892 Practice for Packaging/Packing of PlasticsE177 Practice for Use of th

9、e Terms Precision and Bias inASTM Test MethodsIEEE/ASTM SI-10 Use of the International System of Units(SI):The Modern Metric System2.2 ISO Standards:ISO 12086-1 PlasticsFluoropolymer Dispersions andMoulding and Extrusion MaterialsPart 1ISO 12086-2 PlasticsFluoropolymer Dispersions andMoulding and Ex

10、trusion MaterialsPart 23.Terminology3.1 Definitions:3.1.1 GeneralThe terminology given in TerminologyD883 is applicable to this specification.3.1.2 lot,none production run or a uniform blend of twoor more production runs.3.1.3 Abbreviated Terms:3.1.4 GeneralThe abbreviated terms given in Terminol-og

11、y D1600 are applicable to this specification.4.Classification4.1 This specification covers five types of modified ETFEfluoropolymer supplied in pellet form classified according totheir specific gravity.The resins of each type are divided intoone to three grades according to their melt flow rate.4.2

12、A one-line system shall be used to specify materialscovered by this specification.The system uses predefined cellsto refer to specific aspects of this specification,as illustrated asfollows:1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibilit

13、y of Subcommittee D20.15 on ThermoplasticMaterials(Section D20.15.12).Current edition approved Sept.1,2015.Published September 2015.Originallyapproved in 1973.Last previous edition approved in 2010 as D3159-10.DOI:10.1520/D3159-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,or

14、contact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Co

15、nshohocken,PA 19428-2959.United States1 SpecificationStandard Number:Type:Grade:SpecialBlock:Notes:,:Example:Specification D3159 95,I2For this example,the line callout shall be,SpecificationD3159 95,I2 and shall specify a modified ETFE fluoropoly-mer that has all of the properties listed for that ty

16、pe and gradein Tables 1 and 2.A comma is used as the separator betweenthe standard number and the type.Separators are not neededbetween the type and grade.35.General Requirements5.1 The material shall be of uniform composition and soprepared as to conform to the requirements of this specifica-tion.5.2 The material described in this specification shall be freeof foreign matter to such a contamination level as shall beagreed upon between the purchaser and the seller.6.Performance Requirements6.1 T

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2