1、Designation:D325686(Reapproved 2020)Standard Test Methods forChemical Analysis of Phthalocyanine Blue and GreenPigments1This standard is issued under the fixed designation D3256;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the yea
2、r of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover procedures for the qualitativechemical analysis of pigments known commercially as copperphtha
3、locyanine blue and green.1.2 The procedures appear in the following order:SectionIdentification5Moisture and Other Volatile Matter6Detection of Basic Dye Derivatives7Detection of Other Organic Coloring Matter8Detection of Ultramarine Blue9Detection of Iron Blue or Chrome Green101.3 The values stated
4、 in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,an
5、d environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International
6、Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D280 Test Methods for Hygroscopic Moisture(and OtherMatter Volatile Under the Test Conditions)in PigmentsD1193 Specification for Reagent Wat
7、er3.Significance and Use3.1 These test methods are suitable for determining ifimpurities are present and establishing that the required pig-ments are present.These test methods may be used formanufacturing and purchasing quality control.4.Reagents4.1 Purity of ReagentsReagent grade chemicals shall b
8、eused in all tests.Unless otherwise indicated,it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused,provided it is first ascertained that the reage
9、nt is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.4.2 Purity of WaterUnless otherwise indicated,referencesto water shall be understood to mean Type II reagent gradewater conforming to Specification D1193.5.Identification5.1 To about 0.05 g of the s
10、ample in a 50-mL beaker,add 30mL of sulfuric acid(H2SO4,sp gr 1.84).Stir occasionally for15 min,heating if necessary to accelerate the solution of thepigment.Formation of a dark greenish yellow solution indi-cates phthalocyanine blue and a dark reddish color indicatesbrominated green pigment.Pour th
11、e solution into 250 mL ofwater and stir.The phthalocyanine pigment should immedi-ately precipitate as a flocculent mass.5.2 Filter off the precipitate,washing once or twice withwater.Scrape a small amount of the precipitate off the filter,place on a clean platinum wire moistened with hydrochloricaci
12、d(HCl),and subject it to the low flame of a bunsen burner.As the precipitate burns,a light blue-green flame should beclearly evident.This indicates organically combined copper.NOTE1Characteristic spectrophotometric absorption spectra in the1These test methods are under the jurisdiction of ASTM Commi
13、ttee D01 onPaint and Related Coatings,Materials,and Applications and are the directresponsibility of Subcommittee D01.31 on Pigment Specifications.Current edition approved June 1,2020.Published July 2020.Originally approvedin 1973.Last previous edition approved in 2014 as D3256 86(2014).DOI:10.1520/
14、D3256-86R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3ACS Reagent Chemicals,Specifications and Procedures f
15、or Reagents andStandard-Grade Reference Materials,American Chemical Society,Washington,DC.For suggestions on the testing of reagents not listed by the American ChemicalSociety,see Analar Standards for Laboratory Chemicals,BDH Ltd.,Poole,Dorset,U.K.,and the United States Pharmacopeia and National For
16、mulary,U.S.Pharma-copeial Convention,Inc.(USPC),Rockville,MD.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1near infrared ra
