1、L+Y-5 5 5/ASTM D335b 88=0757510 0027376 5 W Designation:D 3356-88 AMERICAN SOCIETY FOR TESTINO AND MATERIALS 1916 Race St.,Philadelphia,Pa.19103 Repnnled from the Annual Eookof ASTM Standards,Copyright ASTM If not listed in lhe current combined index,will appear In the next edition.Standard specific
2、ation for Fittings for Bituminized Fiber Drain and Sewer Pipe This standard is issued under the fixed designation D 3356;the number immediately foliowing the designation indicates the year of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the
3、 year of last reapproval.A superscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope 1.1 This specification covers fittings suitable for use with both homogeneous and laminated-wall types of bituminized fiber pipe.2.Referenced Documents 2.1 ASTh Standards:D 18
4、6 1 Specification of Homogeneous Bituminized Fiber Drain and Sewer Pipe D 1862 Specification for Laminated-Wal Bituminized Fiber Drain and Sewer Pipe D 23 1 1 Specification for Perforated,Homogeneous Bituminized Fiber Pipe for General Drainage2 D 23 12 Specification for Perforated,Homogeneous Bitumi
5、nized Fiber Pipe for Septic Tank Disposal Fields D 23 13 Specification for Perforated,Laminated-Wall Bituminized Fiber Pipe for Septic Tank Disposal Fields D 23 14 Methods of Testing Homogeneous Bituminized Fiber Pipe D 23 15 Methods of Testing Laminated-Wall Bituminized Fiber Pipe2 D 23 16 Recommen
6、ded Practice for Installing Bituminized Fiber Drain and Sewer Pipe D 24 17 Specification for Perforated,Laminated-Wall Bituminized Fiber Pipe for General Drainage2 D 24 18 Specification for Perforated,Laminated-Wall Bituminized Fiber Pipe for Airport and Highway Drainage2 D 28 18 Specification for P
7、erforated,Homogeneous Bituminized Fiber Pipe for Airport and Highway Drainage2 3.Materials and Manufacture 3.1 Fittings may be fabricated from the same material as the pipe or may be molded.Couplings and adapters other than bituminized fiber material may be used,provided they have equal or better ph
8、ysical and chemical properties.3.2 Joints:3.2.1 The Type I taper shall be accurately machined or 3.2.2 All joints for a given size shall be interchangeable,molded to the dimensions shown in Fig.I.and shall be watertight when assembled with the pipe.This specification is under the jurisdiction of AST
9、M Committee D-8 on Roofing,Waterproofing,and Bituminous Materiais and is the direct responsibility of Subcommittee W8.16 on Bituminous Fiber Pipe.Current edition approved Feb.1,1988.Published April 1988.Originally published as D 3356-74 T.Last previous edition D 3356-8 I.ZAiiniiaI Book o f ASTM Stan
10、dards,Vol 04.04.f 4.Physical and Chemical Requirements 4.1 All fittings used with homogeneous pipe shall meet pipe test requirements specified in Specification D 186 1,and the fittings used with laminated pipe shall comply with the pipe requirements of Specification D 1862.4.2 The minimum strength r
11、equirements for a fitting shall be the same as those required for the largest size pipe that is connected to it.4.3 Methods for testing homogeneous pipe are described in Methods D 2314,and methods for laminated pipe are described in Methods D 2315.Where practical and if the fitting shape lends itsel
12、f to test,these same test methods may be used to evaluate a fitting for use with a particular size and type of pipe.5.Dimensions 5.I Fittings shall meet the manufacturers dimensional specifications and shall be acceptable to the user.5.2 A testing ball 7 mm(Y4 in.)less in diameter than the nominal p
13、ipe size shall readily pass through all fittings.5.3 Approximate outside dimensions of commercially accepted fittings used with bituminized fiber pipe are shown in the attached fittings drawings(see Figs.1 through 30).6.Basis of Acceptance 6.1 The types of tests required and number of fittings to be
14、 tested shall be mutually agreed upon between the pur-chaser and the supplier for any size lot.NOTE-All dimensions of the following figures are shown in millimetres(inches).Dotted lines indicate the manufacturers option.All dimensions are subject to the manufacturers tolerances.L WN.-i DRIVE MIN.I V
15、 COUPLINO PIPE Dimensions,mm(in.)Size L F J Drive 50(2)54.4(2.14)25.4(1.00)62.0(2.44)2.5(0.10)75(3)64.3(2.53)30.5(1.20)86.6(3.41)2.5(0.10)100(4)85.1(3.35)40.6(1.60)113.5(4.47)2.5(0.10)125(5)101.6(4.00)49.5(1.95)144.0(5.67)5.1(0.20)150(6)101.6(4.00)49.5(1.95)170.2(6.70)5.1(0.20)200(8)127.0(5.00)63.0(
16、2.48)233.7(9.20)6.4(0.25)FIG.1 Fiber Coupling(Straight)NOTICE:This standard has either been superseded and replaced by a new version or discontinued.Contact ASTM International(www.astm.org)for the latest information.ASTM D335b 88 0759510 0027777 7 H Dimensions,mm(in.)(Y=5 O J O Size 62.0(2.44)76.2(3.0)86.9(3.42)88.9(3.5)50(2)113.5(4.47)101.6(4.0)75(3)1 O0(4)125(5)144.0(5.67)101.6(4.0)150(6)170.4(6.71)101.6(4.0)200(8)233.7(9.2)127.0(5.0)(Y=11 1/40(Y=15 J O J O 62.0(2.44)76.2(3.0)62.0(2.44)76.2(3.
