收藏 分享(赏)

ASTM_D_3455_-_11_2019.pdf

上传人:益****师 文档编号:179844 上传时间:2023-03-04 格式:PDF 页数:3 大小:68.13KB
下载 相关 举报
ASTM_D_3455_-_11_2019.pdf_第1页
第1页 / 共3页
ASTM_D_3455_-_11_2019.pdf_第2页
第2页 / 共3页
ASTM_D_3455_-_11_2019.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D345511(Reapproved 2019)Standard Test Methods forCompatibility of Construction Material with ElectricalInsulating Oil of Petroleum Origin1This standard is issued under the fixed designation D3455;the number immediately following the designation indicates the year oforiginal adoption or,i

2、n the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover screening for the compatibilityof materials of construction wit

3、h electrical insulating oil for usein electrical equipment.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespon

4、sibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-izatio

5、n established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D877 Test Method for Dielectric Breakdown Voltage ofInsulati

6、ng Liquids Using Disk ElectrodesD924 Test Method for Dissipation Factor(or Power Factor)and Relative Permittivity(Dielectric Constant)of Electri-cal Insulating LiquidsD971 Test Method for Interfacial Tension of Oil AgainstWater by the Ring MethodD974 Test Method for Acid and Base Number by Color-Ind

7、icator TitrationD1500 Test Method for ASTM Color of Petroleum Products(ASTM Color Scale)D2413 Practice for Preparation of Insulating Paper andBoard Impregnated with a Liquid DielectricD3487 Specification for Mineral Insulating Oil Used inElectrical Apparatus3.Significance and Use3.1 The magnitude of

8、 the changes in the electrical propertiesof the insulating oil are of importance in determining thecontamination of the oil by the test specimen.3.2 Physical and chemical changes in the oil such as color,interfacial tension and acidity,also indicate solubility or otheradverse effects of the test spe

9、cimen on the oil.3.3 Physical changes of the test specimen such as hardness,swelling,and discoloration show the effect of the oil on the testspecimen and are used to determine the suitability of thematerial for use in insulating oil.3.4 A material meeting the criteria recommended does notnecessarily

10、 indicate suitability for use in electrical equipment.Other properties must also be considered.Additionally,certainmaterials containing additives may meet the requirements ofthese test methods,yet be unsatisfactory when subjected tolonger term evaluations.Examples of such materials arepolyvinyl chlo

11、ride(PVC)based compounds,nylon and elasto-meric compounds.4.Apparatus4.1 Sample-Handling Apparatus:4.1.1 Oven,forced-draft,adjustable to 100 6 1 C,and adrying oven,adjustable to 105 6 5 C.4.1.2 Glass Containers,1-L,fitted with glass or aluminumfoil covers.NOTE1Other materials have been found to be s

12、uitable as covers.4.2 Sample-Testing Apparatus:4.2.1 Tensile StrengthAs specified in appropriate testmethod.4.2.2 HardnessAs specified in appropriate test method.4.2.3 Dimensional ChangeMicrometer and caliper.4.2.4 Weight ChangeAnalytical balance.1These test methods are under the jurisdiction of AST

13、M Committee D27 onElectrical Insulating Liquids and Gases and are the direct responsibility ofSubcommittee D27.06 on Chemical Test.Current edition approved Dec.1,2019.Published December 2019.Originallyapproved in 1975.Last previous edition approved in 2011 as D3455 2011.DOI:10.1520/D3455-11R19.2For

14、referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Con

15、shohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Orga

16、nization Technical Barriers to Trade(TBT)Committee.15.Preparation of Test Specimen5.1 Test specimen size shall be such that the ratio of surfacearea to oil volume is four times as large as the ratio encoun-tered in normal use in electrical equipment unless there is somespecial reason for using a different ratio(Note 2).Somesuggested ratios are as follows:5.1.1 If the test specimen can be measured,no less than 52cm2are used with each 800 mL of oil.5.1.2 If the test specimen is insoluble in oil an

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2