1、Designation:D3909/D3909M14(Reapproved 2021)Standard Specification forAsphalt Roll Roofing(Glass Felt)Surfaced with MineralGranules1This standard is issued under the fixed designation D3909/D3909M;the number immediately following the designation indicates theyear of original adoption or,in the case o
2、f revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.This specification replace
3、s Federal Specification SS-R-630,Class 3.1.Scope1.1 This specification covers asphalt-impregnated andcoated glass felt roll roofing surfaced on the weather side withmineral granules,for use as a cap sheet in the construction ofbuilt-up roofs.1.2 The values stated in either SI units or inch-pound uni
4、tsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in nonconformancewith the standard.1.3 This international standard was developed in a
5、ccor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM
6、 Standards:2D228/D228M Test Methods for Sampling,Testing,andAnalysis of Asphalt Roll Roofing,Cap Sheets,andShingles Used in Roofing and WaterproofingD1079 Terminology Relating to Roofing and Waterproofing3.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to Terminol
7、ogy D1079.4.Materials and Manufacture4.1 The glass felt shall be a thin,porous sheet composedpredominately of fine glass fibers uniformly deposited in anonwoven pattern.The felt may be reinforced with random orparallel oriented glass yarns,or both,which may be gathered ortwisted,bonded,or unbonded.T
8、he felt shall contain a water-insoluble agent.4.2 In the process of manufacture,the glass mat shall beuniformly impregnated and coated on both sides with anasphaltic material,permitted to be compounded with a mineralstabilizer.4.3 The weather side shall be uniformly surfaced withmineral granules fir
9、mly embedded in the asphaltic coating,except for any selvage.4.4 The reverse side shall be covered with a material toprevent sticking in the roll.5.Physical Properties5.1 The material shall conform to the dimensions andmasses prescribed in Table 1 and areas prescribed in Table 2.5.2 The finished pro
10、duct shall not crack nor be so sticky asto cause tearing or other damage upon being unrolled attemperatures between 10 and 60 C 50 and 140 F.5.3 Pliability at 25 C 77 FAt least eight strips out often from the granule-surfaced portion of the sheet shall notcrack when tested in accordance with Section
11、 10 of TestMethods D228/D228M.5.4 Mass Loss and Behavior on HeatingThere shall be nomore than 1.5%volatile loss,and the granular surfacing shallnot slide more than 2 mm 116in.when tested in accordancewith Section 11 of Test Methods D228/D228M.6.Workmanship,Finish,and Appearance6.1 The glass felt sha
12、ll be thoroughly and uniformly im-pregnated with asphalt and shall show no uncoated fibers.Thefiber pattern may be discernible on the back side.6.2 The surface of the weather side shall be uniform infinish and texture.The mineral granules shall be uniformly1This specification is under the jurisdicti
13、on of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved Nov.15,2021.Published November 2021.Originallyapproved in 1980.Last previous edition approved in 2014 as D3909/D3909M 1
14、4.DOI:10.1520/D3909_D3909M-14R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100
15、Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommen
16、dations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1?distributed in a smooth layer over the entire surface,except forany selvage,and shall be firmly embedded in the asphaltcoating.6.3 When a selvage is provided,the line of demarcationbetween the surfaced and unsurfaced portions of the sheet shallbe straight and parallel to the edges of the sheet.A suitablematerial shall be applied to prevent sticking of the coatedselvage in the roll.6.4 The asphalt coating a
