1、Designation:D313821An American National StandardStandard Specification forSolvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene(ABS)and Poly(Vinyl Chloride)(PVC)Non-Pressure Piping Components1This standard is issued under the fixed designation D3138;the number immediately fol
2、lowing the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved f
3、or use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification provides general requirements forsolvent cements used in joining acrylonitrile-butadiene-styrene(ABS)plastic pipe or fittings to poly(vinyl chloride)(PVC)plastic pipe or fittings.1.2 These cements are intended for use
4、 in cementing tran-sition joints between ABS and PVC materials in non-pressureapplications only(25 psi(170 kPa)or less).NOTE1This specification was developed to provide a means forjoining an ABS non-pressure piping system using a solvent-cementedtransition joint,for example,joining ABS building drai
5、n to a PVC sewersystem.The intention was not to create a specification for an all purposeABS-PVC solvent cement that would be used for mixing ofABS and PVCpiping materials nor to specify a cement that could generally be used foreither material.Specific cements for ABS or PVC components should beused
6、(see 1.3).1.3 Solvent cements used for joining PVC pipe and fittingsare specified in Specification D2564.Solvent cements used forjoining ABS pipe and fittings are specified in SpecificationD2235.1.4 Arecommended procedure for joiningABS to PVC pipeand fittings for non-pressure applications is given
7、in theappendix.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 The following safety hazards caveat pertains only to thetest method
8、s portion,Section 6,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregula
9、tory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Orga
10、nization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1084 Test Methods for Viscosity of AdhesivesD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Classification System and Basis for Specification forRigid Poly(Vinyl Chloride)(PVC)Compounds and
11、 Chlo-rinated Poly(Vinyl Chloride)(CPVC)CompoundsD2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe and FittingsD2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2661 Specification for Acrylonitrile-Butadiene-Styrene(A
12、BS)Schedule 40 Plastic Drain,Waste,and Vent Pipeand FittingsD2665 Specification for Poly(Vinyl Chloride)(PVC)PlasticDrain,Waste,and Vent Pipe and FittingsF402 Practice for Safe Handling of Solvent Cements,Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating t
13、o Plastic Piping SystemsF493 Specification for Solvent Cements for ChlorinatedPoly(Vinyl Chloride)(CPVC)Plastic Pipe and Fittings3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.1Th
14、is specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.Current edition approved Nov.1,2021.Published November 2021.Originallyapproved in 1972.Last previous edition approved in 2016 as D3138 04(2016)
15、.DOI:10.1520/D3138-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the
16、 end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1?4.Materials and Manufacture4.1 The solvent cement shall
