收藏 分享(赏)

ASTM_D_3633_-_D_3633M_-_12_2019.pdf

上传人:益****师 文档编号:180142 上传时间:2023-03-04 格式:PDF 页数:4 大小:137.38KB
下载 相关 举报
ASTM_D_3633_-_D_3633M_-_12_2019.pdf_第1页
第1页 / 共4页
ASTM_D_3633_-_D_3633M_-_12_2019.pdf_第2页
第2页 / 共4页
ASTM_D_3633_-_D_3633M_-_12_2019.pdf_第3页
第3页 / 共4页
ASTM_D_3633_-_D_3633M_-_12_2019.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D3633/D3633M12(Reapproved 2019)Standard Test Method forElectrical Resistivity of Membrane-Pavement Systems1This standard is issued under the fixed designation D3633/D3633M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,t

2、he year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the measurement of the electri-cal resistivity of water-barrier membrane-pavement system

3、swhen applied to concrete bridge decks.1.2 Measurements shall be performed on the bituminouspavement surface covering the water-barrier membrane.1.3 This test method utilizes a measure of electrical resis-tance between the saturated top surface of the water-barriermembrane and the reinforcing steel

4、embedded in the concretebridge deck.1.4 The values measured represent the electrical resistanceobtained with the equipment and procedures stated herein anddo not necessarily agree or correlate with those using otherequipment or procedures.1.5 UnitsThe values stated in either SI units or inch-pound u

5、nits are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in noncon-formance with the standard.1.6 This standard does not purport to addre

6、ss all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed i

7、n accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 A

8、STM Standards:2C670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsD3743 Terminology Relating to Bridge Deck and Substruc-ture Protection(Withdrawn 2004)3D4071 Practice for Use of Portland Cement Concrete BridgeDeck Water Barrier Membrane SystemsE105 P

9、ractice for Probability Sampling of Materials3.Terminology3.1 For definitions of terms used in this test method,refer toTerminology D3743.4.Significance and Use4.1 This test method for measuring the electrical resistivityof water-barrier membrane-pavement systems may be inter-preted to indicate the

10、effectiveness of such systems.4.2 This test method is predicated on the fact that anelectrical connection between the surface of the pavement andthe reinforcing steel in the concrete pavement cannot be madethrough an impermeable water-barrier membrane.4.3 This test method may be used for acceptance

11、when theaccepting agency specifies the minimum resistance valuedesired.5.Apparatus5.1 Ohmmeter,dc,20 000/V rating connected to adouble-pole,double-throw switch box or ac ohmmeter(switchbox not required).NOTE1When this test method is used for acceptance,the acceptingagency should specify the type of

12、ohmmeter to be used.1This test method is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.32 onBridges and Structures.Current edition approved July 1,2019.Published July 2019.Originally approvedin 1977.Last previous edition

13、 approved in 2012 as D3633/D3633M 12.DOI:10.1520/D3633_D3633M-12R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM websit

14、e.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on stan

15、dardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.2 Insulated Wire,No.18,Belden test probewire or equiva-lent.Two spools,minimum 38 m 125

16、ft.5.3 Copper Plate,305 by 305 by 3.0 mm 12 by 12 by18in.,with the means for connecting the ohmmeter lead anda wooden handle approximately 1 m 39 in.in length.5.4 Polyurethane Sponge,305 by 305 by 13 mm 12 by 12by12in.,to be attached to the copper plate with rubber bandsor other suitable means.When assembled,this apparatus iscalled the probe.5.5 Pressure Spray Can,12-L 3-gal capacity,with a hoseand spray nozzle.6.Reagent6.1 A wetting agent which,when added to the water,willbreak the surface tens

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2