1、Designation:D2672201An American National StandardStandard Specification forJoints for IPS PVC Pipe Using Solvent Cement1This standard is issued under the fixed designation D2672;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the yea
2、r of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTESections 2.1 and 4.2 were editorially corrected in February 2021.1.Scope*1.1 This specification covers the socket produced f
3、or sol-vent cement joints on both pressure and non-pressure IPS pipe.It also covers the testing of the joints on both pressure andnon-pressure pipe,and includes requirements for socketdimensions,burst pressure,and joint tightness tests of thesolvent cemented joints.The tests described are not intend
4、edfor routine quality control,but rather to evaluate the perfor-mance characteristics of the joint.NOTE1On dual marked Schedule 40 DWV and potable water pipe,the socket bells must conform to the dimensional and physical require-ments for pressure socket bells.1.2 The text of this specification refer
5、ences notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses a
6、re mathematicalconversions to SI units that are provided for information onlyand are not considered standard.NOTE2Changes in ground,water,or air temperature will produceexpansion or contraction forces in PVC piping,and these will result inlongitudinal shear stresses in the solvent cement joints.Thes
7、e stressesmust be considered in the design and operation of the system.NOTE3See Practice D618 for information relating to this specifica-tion.1.4 The following safety hazards caveat pertains only to thetest method portion,Section 10,of this specification.Thisstandard does not purport to address all
8、of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.5 This international standard was developed in accor-da
9、nce with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standa
10、rds:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1785 Specification for Poly(Vinyl Chloride)(PVC)PlasticPipe,Schedules 40,80,and 120
11、D2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2241 Specification for Poly(Vinyl Chloride)(PVC)Pressure-Rated Pipe(SDR Series)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2665 Specification for Poly(Vinyl Chloride)(PVC)P
12、lasticDrain,Waste,and Vent Pipe and FittingsD2855 Practice for the Two-Step(Primer and Solvent Ce-ment)Method of Joining Poly(Vinyl Chloride)(PVC)orChlorinated Poly(Vinyl Chloride)(CPVC)Pipe andPiping Components with Tapered SocketsF412 Terminology Relating to Plastic Piping SystemsF512 Specificatio
13、n for Smooth-Wall Poly(Vinyl Chloride)(PVC)Conduit and Fittings for Underground InstallationF656 Specification for Primers for Use in Solvent CementJoints of Poly(Vinyl Chloride)(PVC)Plastic Pipe andFittingsF3328 Practice for the One-Step(Solvent Cement Only)Method of Joining Poly(Vinyl Chloride)(PV
14、C)or Chlo-rinated Poly(Vinyl Chloride)(CPVC)Pipe and PipingComponents with Tapered Sockets1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.Current edition approved Aug.1,2020.Published Augu
15、st 2020.Originallyapproved in 1968.Last previous edition approved in 2014 as D2672 14.DOI:10.1520/D2672-20E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standar
16、ds Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical B
