1、Designation:D238004(Reapproved 2019)Standard Test Method forMethanol Content of Formaldehyde Solutions1This standard is issued under the fixed designation D2380;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method provides for the calculation of themethanol content of commercially available 37%formalde-hyde solutions and is based
3、on the relationship of specificgravity to formaldehyde and methanol content.2Separateequations are given for three ranges of methanol:0 to 2%,6 to8%,and 12 to 15%.1.2 For purposes of determining conformance of an ob-served or a calculated value using this test method to relevantspecifications,test r
4、esult(s)shall be rounded off“to the nearestunit”in the last right-hand digit used in expressing thespecification limit,in accordance with the rounding-off methodof Practice E29.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.
5、1.4 For hazard information and guidance,see the suppliersMaterial Safety Data Sheet.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental pr
6、actices and deter-mine the applicability of regulatory limitations prior to use.Specific hazard statements are given in Section 4.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for
7、theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D268 Guide for Sampling and Testing Volatile Solvents andChemical Intermediates for Use in Paint and Related
8、Coatings and MaterialD2194 Test Method for Concentration of FormaldehydeSolutionsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3.Significance and Use3.1 This test method provides a measurement of methanolcontent of formaldehyde solutions.The result
9、s of these mea-surements can be used for specification acceptance.3.2 This test method is applicable to 37%formaldehydesolutions containing 0 to 2%,6 to 8%,or 12 to 15%methanol.4.Hazards4.1 Formaldehyde and formaldehyde solutions are hazard-ous.Minimize exposure and contact to avoid acute effects an
10、dpossible sensitizing.Consult the suppliers Material SafetyData Sheet for specific hazard information.5.Procedure5.1 Determine the apparent specific gravity of the materialby a method that is accurate to the fourth decimal place,thetemperature of both the specimen and the water being 25 C.See Guide
11、D268.5.2 Determine the formaldehyde content of the material inaccordance with Test Method D2194.6.Calculation6.1 Calculate the methanol content as follows using theappropriate equation for the expected methanol range:1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Relat
12、ed Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents,Plasticizers,and Chemical Intermediates.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 1965.Last previous edition approved in 2011 as D2380 04(2011).DOI:10.1520
13、/D2380-04R19.2Walker,J.F.,Formaldehyde,3rd edition,1964,pp.8691.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Co
14、pyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of Internationa
15、l Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.1.1 0 to 2%Methanol:Methanol,wt%51.001710.003F 2 D!/0.00253(1)6.1.2 6 to 8%Methanol:Methanol,wt%51.001510.003F 2 D!/0.00250(2)6.1.3 12 to 15%Methanol:Methanol,wt%51.021010.0025
16、F 2 D!/0.00257(3)where:F=formaldehyde content,weight%,andD=specific gravity at 25/25 C.NOTE1The numerical factors were calculated from the slope of themethanol curve of a nomograph relating specific gravity at 25/25 C tomethanol-formaldehyde content.7.Report7.1 Report the methanol content to the nearest 0.1%.8.Precision and Bias8.1 In an interlaboratory study of this test method,thewithin-laboratory standard deviation was found to be 0.10%absolute with 28 degrees of freedom and the between-labor
