1、Designation:D437321Standard Test Method for Rapid Determination ofCarbonate Content of Soils1This standard is issued under the fixed designation D4373;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number
2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of carbonatecontent of soils and soft rock which can be readily brokendown by mechanical effort.It is
3、a gasometric method that usesa simple portable apparatus.Results should be clearly stated asthe calcite equivalent in percent because different carbonatespecies cover a wide range of percent calcite equivalent asshown below for a number of carbonates:SpeciesCationCalciteEquivalent,%MagnesiteMg117.0D
4、olomiteCa,Mg108.6CalciteCa100.0AragoniteCa100.0RhodocrositeMn87.1SideriteFe86.4SmithsoniteZn79.8WitheriteBa50.7CerrusitePb37.5For example,a 100%dolomite would be expected to yield108.6%calcite equivalent while 100%siderite would yieldonly 86.4%calcite equivalent.Calcite and aragonite reactionswill t
5、ypically complete within about 10 minutes.This methoddoes not distinguish between the carbonate species and suchdetermination must be made using quantitative chemical analy-sis methods such as atomic absorption.1.2 UnitsThe values stated in SI units are to be regardedas standard.The values given in
6、parentheses are provided forinformation only and are not considered standard.Reporting oftest results in units other than SI shall not be regarded asnonconformance with this standard1.3 All observed and calculated values shall conform to theguidelines for significant digits and rounding established
7、inPractice D6026.1.3.1 The procedures used to specify how data are collected/recorded or calculated,in this standard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that generally should be retained.The proce-dures used do not consider material varia
8、tion,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to becommensurate with these considerations.It is beyond the scopeof this standard to consider significant dig
9、its used in analyticalmethods for engineering design.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the appl
10、icability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by t
11、he World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C25 Test Methods for Chemical Analysis of Limestone,Quicklime,and Hydrated LimeD653 Terminology Relating to Soil,Rock,and ContainedFluidsD3042 Test Method for Insoluble Residue in Carbonate
12、AggregatesD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD4753 Guide for Evaluating,Selecting,and Specifying Bal-ances and Standard Masses for Use in Soil,Rock,andConstruction Materials TestingD60
13、26 Practice for Using Significant Digits in GeotechnicalDataE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3.Terminology3.1 DefinitionsFor definitions of common technical termsused in this standard,refer to Terminology D653.1This test method is under the jurisdiction ofASTM Committe
14、e D18 on Soil andRock and is the direct responsibility of Subcommittee D18.06 on Physical-ChemicalInteractions of Soil and Rock.Current edition approved June 15,2021.Published June 2021.Originallyapproved in 1984.Last previous edition approved in 2014 as D4373 14.DOI:10.1520/D4373-21.2For referenced
15、 ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM I
16、nternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.Summary of Test Method4.1 A representative sample is oven dried and then pulver-ized to pas
