1、Designation:D273997(Reapproved 2017)Standard Test Method forVolume Resistivity of Conductive Adhesives1This standard is issued under the fixed designation D2739;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the volumeresistivity of resin-based conductive adhesives in the curedcondition.The test i
3、s made on a thin adhesive layer as preparedin a bonded specimen.This test method is used for conductiveadhesives that are cured either at room temperature or atelevated temperatures.1.2 The values stated in either SI or other units shall beregarded separately as standard.SI equivalents to screwthrea
4、ds are shown in the figures.1.3 This standard does not purport to address the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety,health,and environmental practices and determine the appli-cability of regulatory limitatio
5、ns prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization Techn
6、icalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD907 Terminology of Adhesives2.2 Federal Specification:QQ-B-626 Composition 2232.3 ASTM Adjuncts:Assembly Jig43.Terminology3.1 Definitions:3.1.1 Many terms in this test me
7、thod are defined in Termi-nology D907.3.1.2 conductivity,nthe ratio of the current density carriedthrough a specimen to the potential gradient paralleling thecurrent.This is numerically equal to the conductance betweenopposite faces of a unit cube of liquid.It is the reciprocal ofresistivity.D2864,D
8、273.1.3 resistivity,volume,nthe ratio of the electric potentialgradient to the current density when the gradient is parallel tothe current in the material.D1566,D114.Summary of Test Method4.1 The volume resistivity of adhesive layers cured betweenmetal adherends is measured on a resistance bridge.Te
9、nsileadhesion plugs(Fig.1)5are described in this test method.Anyother test specimens and materials can be used as long assimilar precautions(see Section 7)are observed regardingpreparation and tolerances.5.Significance and Use5.1 Accurate measurement of the volume resistivity ofconductive adhesives
10、is important,particularly with respect toapplications in electronic packaging techniques.This methodmeasures the resistance of conductive adhesives used in thinfilms as part of a bonded assembly.This does not imply that themeasured results are applicable to different configurations withdifferent met
11、als.This method may be used for acceptancetesting and for screening materials.6.Apparatus6.1 Kelvin(Resistance)Bridge,calibrated to 1%accuracy.66.2 With the agreement of the interested parties,any metaltensile adhesion plugs(Fig.1)can be used to prepare thetensile adhesion specimens.NOTE1Different m
12、etals will inherently provide different resistance1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.80 on MetalBonding Adhesives.Current edition approved Nov.1,2017.Published November 2017.Originallyapproved in 1968.Las
13、t previous edition approved in 2010 as D2739 97(2010).DOI:10.1520/D2739-97R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe A
14、STM website.3Available from DLA Document Services,Building 4/D,700 Robbins Ave.,Philadelphia,PA 19111-5094,http:/quicksearch.dla.mil.4Detailed drawings of the assembly jig are available from ASTM InternationalHeadquarters.Order Adjunct No.ADJD2739.Original adjunct produced in 1987.5Plugs to accommod
15、ate banana plugNo.192,Herman H.Smith,Inc.,orequivalent.6Satisfactory resistance bridges are made by:Leads and Northup Co.BridgeCatalog No.4306,Minneapolis Honeywell Division Catalog No.1622,and BiddleInstruments Catalog No.603282.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Co
16、nshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 values.The measured resistance is dependent on resistance at theadhesive-adherend interface due to metal oxide formation.The extent ofoxide format
