1、Designation:D263215(Reapproved 2019)Standard Test Method forRubber PropertyResilience by Vertical Rebound1This standard is issued under the fixed designation D2632;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of im
3、pactresilience of solid rubber from measurement of the verticalrebound of a dropped mass.1.2 This test method is not applicable to the testing ofcellular rubbers or coated fabrics.1.3 A standard test method for impact resilience and pen-etration of rubber by a rebound pendulum is described in TestMe
4、thod D1054.1.4 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establ
5、ish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for
6、 theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD832 Practice for Rubber Conditioning For Low Tempera-tu
7、re TestingD1054 Test Method for Rubber PropertyResilience Usinga Goodyear-Healey Rebound Pendulum(Withdrawn2010)3D1349 Practice for RubberStandard Conditions for Test-ingD1566 Terminology Relating to RubberD3182 Practice for RubberMaterials,Equipment,and Pro-cedures for Mixing Standard Compounds and
8、 PreparingStandard Vulcanized SheetsD3183 Practice for RubberPreparation of Pieces for TestPurposes from ProductsD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustries2.2 Other Documents:4ISO-10012-1 Quality Assurance Requirements for
9、Measur-ing EquipmentPart 1:Metrological Confirmation Sys-tem for Measuring Equipment5ANSI/NCSL-Z540-1 American National Standard forCalibrationCalibration Laboratories and Measuring andTest EquipmentGeneral Requirements63.Summary of Test Method3.1 Resilience is determined as the ratio of rebound hei
10、ghtto drop height of a metal plunger of prescribed mass and shapewhich is allowed to fall on the rubber specimen.4.Significance and Use4.1 Resilience is a function of both dynamic modulus andinternal friction of a rubber.It is very sensitive to temperaturechanges and to depth of penetration of the p
11、lunger.Consequently,resilience values from one type of reboundinstrument may not,in general,be predicted from results onanother type of rebound instrument.1This test method is under the jurisdiction of ASTM Committee D11 on Rubberand Rubber-like Materials and is the direct responsibility of Subcommi
12、ttee D11.10on Physical Testing.Current edition approved Nov.1,2019.Published December 2019.Originallyapproved in 1967.Last previous edition approved in 2015 as D2632 15.DOI:10.1520/D2632-15R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servi
13、ceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4This test method previously referenced MIL-STD-4662a Military Standard:Calibration Syste
14、m Requirements,which was subsequently canceled by the Depart-ment of Defense in February 1995.These are the DoD recommended replacementdocuments.5Available from the International Organization for Standardization,1 rue deVaremb,Case postale 56,CH-1211,Geneva 20,Switzerland.6Available from the America
15、n National Standards Institute,25 W.43rd St.,4thFloor,New York,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization es
16、tablished in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.2 This test method is used for development and compari-son of materials.It may not directly relate to end-use perfor-mance.5.Apparatus5.1 A diagram of the essential features and dimensions ofthe apparatus appears in Fig.1.It includes means for suspend-ing a plunger at a given height above the specimen
