1、Designation:D 4166 99(Reapproved 2004)e1An American National StandardStandard Test Method forMeasurement of Thickness of Nonmagnetic Materials byMeans of a Digital Magnetic Intensity Instrument1This standard is issued under the fixed designation D 4166;the number immediately following the designatio
2、n indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.e1NOTENote 1 was added and footnote 2 was editorially
3、 corrected.1.Scope*1.1 This test method covers the measurement of thickness ofany nonmagnetic material by means of a digital magneticintensity instrument.NOTE1The instrument on which this test method is based is nolonger sold or serviced.1.2 This standard does not purport to address all of thesafety
4、 concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.3 There is no similar or equivalent ISO standard.2.Summary of Test Method2.1 I
5、n this test method,a magnetic sensing device iscalibrated and placed on one side of the material to bemeasured.A magnet of known intensity is placed on theopposite side and the distance between the magnet and themagnetic sensing device shows as a digit that can be convertedto inch-pound or metric un
6、its by reference to a table.3.Significance and Use3.1 This test method is useful for measuring the wallthickness of plastic vessels and other plastic structures wherethe geometry of the equipment does not permit direct measure-ment by conventional methods,such as micrometers,calipers,and rulers.This
7、 test method is not limited to plastics and can beused for all nonmagnetic materials.It provides for a rapid andaccurate thickness measurement,without the need for drillingand repair of holes.3.2 Accuracies are not affected by density variations,per-mitting the measurement of composites made up of a
8、 variety ofmaterials of varying densities.By placement of the magneticsource on the mold surface,thickness measurements can bemade during and after fabrication of plastic products to verifythickness and adherence to specifications.4.Interferences4.1 Any instrument measuring the intensity of a magnet
9、icfield can sometimes be influenced by a strong artificial ornatural magnetic field.4.2 Any magnetic material located in the space between themagnet and the sensor will distort the measurement.4.3 A major temperature change(+10F,+5.6C)will causea slight drift in calibration,requiring a recalibration
10、 at the newtemperature prior to making the measurement.5.Apparatus5.1 Micro Digital Magnetic Thickness Sensor2.6.Sampling6.1 Two separate measurements at each location shall betaken.If a variation in excess of 0.01 in.(0.25 mm)appears,athird measurement shall be taken.7.Procedure7.1 CalibrationCalib
11、rate the magnetic sensing device asfollows:7.1.1 Center the magnet supplied with the apparatus on theend of the sensor head and depress the“set button.Thisestablishes the zero measurement point.7.2 Measurement:7.2.1 Place the magnet used in the calibration procedure(7.1)on one side of the material t
12、o be measured.7.2.2 Place the magnetic sensing device on the opposite sideand move it in a criss-cross motion until the digit reaches itslowest point.This denotes that the magnetic sensing device iscentered on the magnet.1This test method is under the jurisdiction ofASTM Committee D20 on Plasticsand
13、 is the direct responsibility of Subcommittee D20.23 on Reinforced PlasticPiping Systems and Chemical Equipment.Current edition approved Oct.,2004.Published October 1,2004.Originallyapproved in 1982.Last previous edition approved in 1999 as D 4166 99.2The sole source of supply of the apparatus known
14、 to the committee was thePolygauge Digital Magnetic Thickness Sensor.If you are aware of alternativesuppliers,please provide this information to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of the responsibletechnical committee1,which you may attend.1
15、*A Summary of Changes section appears at the end of this standard.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.7.2.3 Depress the“set button to lock in the measurementshown in the digital read-out.7.2.4 To perform further measurements,re
16、peat 7.1.1-7.2.3.8.Report8.1 Report the following information:8.1.1 Identification of the material or item measured,8.1.2 Exact location where measurement was made,8.1.3 Condition of two surfaces of material measured,8.1.4 Number of readings taken,and8.1.5 Date of inspection.9.Precision and Bias9.1 In October 1981,an interlaboratory evaluation wasconducted in an ASTM workshop.Persons interested in ob-taining a copy of the research report of this evaluation maycontact ASTM directly.39.1.1 In the
