1、Designation:D300510An American National StandardStandard Specification forLow-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape1This standard is issued under the fixed designation D3005;the number immediately following the designation indicates the year ofori
2、ginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers an electrical insulating tape foruse at lo
3、w temperature down to approximately 18 C(0 F).The tape consists of a backing of vinyl chloride plastic,coatedon one side with a pressure-sensitive adhesive.Four types areincluded providing two thicknesses at two operating tempera-tures.1.2 The values stated in SI units are the standard.The valuesgiv
4、en in parentheses are provided for information purposesonly.2.Referenced Documents2.1 ASTM Standards:2D1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applica-tionsD1711 Terminology Relating to Electrical Insulation3.Terminology3.1 DefinitionsFor def
5、initions of terms in this specifica-tion refer to Terminology D1711.4.Classification4.1 This specification covers two types of vinyl chlorideplastic tape of different thicknesses,as follows:4.1.1 Type I0.0178-mm(0.007-in.)standard backing foruse at low temperature down to 7 C(19.4 F).4.1.2 Type II0.
6、216-mm(0.0085-in.)standard backing foruse at low temperature down to 7 C(19.4 F).4.1.3 Type III0.0178-mm(0.007-in.)standard backing foruse at low temperature down to 18 C(0 F).4.1.4 Type IV0.216-mm(0.0085-in.)standard backing foruse at low temperature down to 18 C(0 F).5.Materials5.1 The backing sha
7、ll be vinyl chloride plastic,suitablycompounded to meet the requirements of this specification.The backing shall be smooth and uniform.The tape edges shallbe straight and unbroken.5.2 The pressure-sensitive adhesive coating shall be smoothand uniform,and essentially free of lumps and bare spots.“Fis
8、h eyes”shall not be cause for rejection.There shall be noadhesive transfer when the tape is unwound from the roll.6.Physical Properties6.1 The tape shall meet the requirements given in Table 1.6.2 Black plastic backing shall be considered standard.Backing of a different color than black shall be spe
9、cified on thepurchase order.7.Standard Rolls7.1 The standard widths and lengths shall be selected fromthe following:7.1.1 Widths:mmin.mmin.614227893825112123011415583811219345027.1.1.1 Widths greater than 2 in.(50 mm)shall be agreedupon between the purchaser and the seller.7.1.2 Lengths:mft620206633
10、1087.1.2.1 Lengths greater than 33 m(108 ft)shall be inmultiples of 108 ft.Additional lengths shall be agreed uponbetween the purchaser and seller.8.Test Methods8.1 The selection of rolls,conditioning,and testing shall bein accordance with Test Methods D1000.1This specification is under the jurisdic
11、tion of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.07 on Flexible and Rigid Insulating Materials.Current edition approved May 1,2010.Published June 2010.Originallyapproved in 1972.Last previous edition approved in 2004 as D
12、300593(2004).DOI:10.1520/D3005-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section ap
13、pears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 9.Rejection9.1 If the test results of any roll do not conform to therequirements prescribed in the specification,two additionalrolls shall be selected and te
14、sted.If one of the two additionalsample rolls also does not conform to the requirements,the lotmay be rejected at the option of the purchaser.10.Packaging and Package Marking10.1 PackagingThe package shall withstand shipment andshall give the product ample protection against damage.Theindividual rol
15、ls shall not adhere to each other or to thecontainer.10.2 Package MarkingEach package shall be marked withthe name of the manufacturer,the manufacturers productnumber,and the width and length of the roll.11.Keywords11.1 electrical insulating tape;low-temperature vinyl chlo-ride plastic tape;plastic
16、electrical tape;pressure-sensitiveadhesive tape;vinyl chloride plastic tapeSUMMARY OF CHANGESCommittee D09 has identified the location of selected changes to this specification since the last issue,D300593(2004),that may impact the use of this specification.(Approved May 1,2010)(1)Revised Table 1.TABLE 1 Requirements for Low-Temperature Vinyl Chloride Plastic Electrical TapePropertiesType IType IIType IIIType IVThickness,mm(in.)avg0.178 0.0250.216 0.0250.178 0.0250.216 0.025(0.007 0.001)(0.0085
