收藏 分享(赏)

ASTM_D_3931_-_08_2015.pdf

上传人:益****师 文档编号:181456 上传时间:2023-03-04 格式:PDF 页数:5 大小:151.83KB
下载 相关 举报
ASTM_D_3931_-_08_2015.pdf_第1页
第1页 / 共5页
ASTM_D_3931_-_08_2015.pdf_第2页
第2页 / 共5页
ASTM_D_3931_-_08_2015.pdf_第3页
第3页 / 共5页
ASTM_D_3931_-_08_2015.pdf_第4页
第4页 / 共5页
ASTM_D_3931_-_08_2015.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D393108(Reapproved 2015)Standard Test Method forDetermining Strength of Gap-Filling Adhesive Bonds inShear by Compression Loading1This standard is issued under the fixed designation D3931;the number immediately following the designation indicates the year oforiginal adoption or,in the ca

2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of compara-tive shear properties of gap-filling adhesi

3、ves in wood-to-woodjoints at specified thicknesses of bondline in the dry condition,when tested on standard specimens under specified conditionsof preparation,conditioning,and loading in compression.Thistest method is intended as an evaluation of gap-filling adhe-sives such as those used to bond ply

4、wood to lumber,lumber tolumber,and other similar materials in building constructions.1.2 This test method also may be used to determine shearproperties of gap-filling adhesives in species of wood and inthicknesses of bondline other than those specified for thecomparative tests of shear properties wi

5、thin this test method.All procedures specified herein are applicable,excepting re-quirements for wood species and specific gravity,and thick-nesses of bondlines.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI u

6、nits that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine t

7、he applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D143 Test Methods for Small Clear Specimens of TimberD905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD1151 Practice for Effect of Moisture and Temperature onAdh

8、esive BondsE171 Practice for Conditioning and Testing Flexible BarrierPackaging3.Terminology3.1 Definitions:3.1.1 gap-filling adhesive,nan adhesive capable of form-ing and maintaining a bond between surfaces that are notclose-fitting.3.1.1.1 DiscussionClose-fitting is relative to a given ma-terial a

9、nd industry;for example,standards in constructiondiffer from standards in electronics.Some adhesives will bondby bridging without completely filling the gap;others by fillingthe gap completely.4.Significance and Use4.1 Structural design based on strength-of-materials prin-ciples requires knowledge o

10、f the mechanical properties of thestructural components,including adhesives.By nature of theiruse,the most important property of adhesive is shear strength.4.2 Shear strength measured by this test method is suitablefor use in adhesive development,manufacturing qualitycontrol,and in materials perform

11、ance specifications,as well asstructural design.5.Apparatus5.1 Testing Machine,having a capacity of about 15 000 lb(6818 kg)in compression or of sufficient capacity to test theadhesive in use.The machine shall be fitted with a shearingtool containing a self-aligning seat to ensure uniform lateraldis

12、tribution of the load.The machine shall be capable ofmaintaining a uniform rate of loading such that the load may beapplied with a continuous motion of the movable head tomaximum load at a rate of 9.20 in.(5.0 mm)/min with apermissible variation of 625%.The shearing tool shown inFig.1 of Test Method

13、 D905 has been found satisfactory.Locatethe testing machine in an atmosphere such that the moisturecontent of the specimens,developed under the conditionsprescribed in 7.3,is not noticeably altered during testing.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is th

14、e direct responsibility of Subcommittee D14.70 on ConstructionAdhesives.Current edition approved April 1,2015.Published April 2015.Originallyapproved in 1980.Last previous edition approved in 2008 as D3931 08.DOI:10.1520/D3931-08R15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,

15、orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Test Specimen and Sam

16、ple6.1 Test specimens for adhesive bonds shall conform to theform and dimensions shown in Fig.1.Prepare bonded assem-blies as described in 7.1.Prepare test specimens for testing asdescribed in 7.2.6.2 Determine mean shear strengths of bonds at bondlinethicknesses of 0.006 and 0.060 in.(0.15 and 1.52 mm).Testsfor strengths of bonds at other thicknesses,in addition to thosespecified,shall be optional upon agreement between themanufacturer and the user.6.3 Test a minimum of 28 specimens,representin

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2