1、Designation:D200012Approved bySociety of Automotive EngineersSAE Recommended Practice J200Standard Classification System forRubber Products in Automotive Applications1This standard is issued under the fixed designation D2000;the number immediately following the designation indicates the year oforigi
2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1
3、.Scope1.1 This classification system covers the properties of vul-canized rubber materials(natural rubber,reclaimed rubber,synthetic rubbers,alone or in combination)that are intendedfor,but not limited to,use in rubber products for automotiveapplications.NOTE1This classification system may serve man
4、y of the needs ofother industries in much the same manner as SAE numbered steels.It mustbe remembered,however,that this system is subject to revision whenrequired by automotive needs.It is recommended that the latest revisionalways be used.1.2 This classification system is based on the premise thatt
5、he properties of all rubber products can be arranged intocharacteristic material designations.These designations aredetermined by types,based on resistance to heat aging,andclasses,based on resistance to swelling in oil.Basic levels arethus established which,together with values describing addi-tion
6、al requirements,permit complete description of the qualityof all elastomeric materials.1.3 In all cases where the provisions of this classificationsystem would conflict with those of the detailed specificationsfor a particular product,the latter shall take precedence.NOTE2When the rubber product is
7、to be used for purposes where therequirements are too specific to be completely prescribed by this classi-fication system,it is necessary for the purchaser to consult the supplier inadvance,to establish the appropriate properties,test methods,and speci-fication test limits.1.4 The values stated in S
8、I units are to be regarded asstandard.2.Referenced Documents2.1 ASTM Standards:2D395 Test Methods for Rubber PropertyCompression SetD412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD429 Test Methods for Rubber PropertyAdhesion toRigid SubstratesD430 Test Methods for Rubber
9、 DeteriorationDynamicFatigueD471 Test Method for Rubber PropertyEffect of LiquidsD573 Test Method for RubberDeterioration in an AirOvenD575 Test Methods for Rubber Properties in CompressionD624 Test Method for Tear Strength of Conventional Vul-canized Rubber and Thermoplastic ElastomersD865 Test Met
10、hod for RubberDeterioration by Heating inAir(Test Tube Enclosure)D925 Test Methods for Rubber PropertyStaining of Sur-faces(Contact,Migration,and Diffusion)D945 Test Methods for Rubber Properties in Compression orShear(Mechanical Oscillograph)D1053 Test Methods for Rubber PropertyStiffening atLow Te
11、mperatures:Flexible Polymers and Coated FabricsD1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1171 Test Method for Rubber DeteriorationSurfaceOzone Cracking Outdoors or Chamber(Triangular Speci-mens)D1329 Test Method for Evaluating Rubber PropertyRetraction at
12、Lower Temperatures(TR Test)D1349 Practice for RubberStandard Temperatures forTesting1This classification system is under the jurisdiction ofASTM Committee D11 onRubber and is the direct responsibility of Subcommittee D11.30 on Classification ofRubber Compounds.Current edition approved Jan.1,2012.Pub
13、lished January 2012.Originallyapproved in 1962.Last previous edition approved in 2008 as D2000 08.DOI:10.1520/D2000-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to th
14、e standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D1418 PracticeforRubberandRubberLaticesNomenclatureD2137 Test Methods for Rubber PropertyBrittleness Pointof Flexible Polymers and Coated
15、 FabricsD2240 Test Method for Rubber PropertyDurometer Hard-nessD3183 Practice for RubberPreparation of Pieces for TestPurposes from ProductsD5964 Practice for Rubber IRM 901,IRM 902,and IRM903 Replacement Oils forASTM No.1,ASTM No.2,andASTM No.3 Oils3.Purpose3.1 The purpose of this classification s
16、ystem is to provideguidance to the engineer in the selection of practical,commer-cially available rubber materials,and further to provide amethod for specifying these materials by the use of a simple“line call-out”designation.3.2 This classification system was developed to permit theaddition of descriptive values for future rubber materialswithout complete reorganization of the classification systemand to facilitate the incorporation of future new test methods tokeep pace with changing industry
