1、Designation:D2178/D2178M15aStandard Specification forAsphalt Glass Felt Used in Roofing and Waterproofing1This standard is issued under the fixed designation D2178/D2178M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of la
2、st revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers glass felts im
3、pregnated tovarying degrees with asphalt intended to be used with asphaltsconforming to the requirements of Specifications D312/D312M or D7654/D7654M in the construction of built-uproofs,and with asphalts conforming to the requirements ofSpecification D449/D449M in the construction of waterproof-ing
4、 systems.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformance
5、with the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.
6、2.Referenced Documents2.1 ASTM Standards:2D146/D146M Test Methods for Sampling and TestingBitumen-Saturated Felts and Woven Fabrics for Roofingand WaterproofingD312/D312M Specification for Asphalt Used in RoofingD449/D449M Specification forAsphalt Used in Dampproof-ing and WaterproofingD1079 Termino
7、logy Relating to Roofing and WaterproofingD7654/D7654M Specification for Asphalt Used in RoofingMeasured by Dynamic Shear Rheometer3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this specification,referto Terminology D1079.3.2 Definitions of Terms Specific to This Standard:3.2.1
8、 net dry massthe mass of the asphalt-impregnatedglass felt exclusive of wrapping and packing material,afterdrying to constant weight and after removing all detachedcomminuted surfacing material as described in 8.2.4.Classification4.1 Asphalt-impregnated glass felts Types IV and VI arecovered by this
9、 specification.5.Materials and Manufacture5.1 The felt shall be a thin,porous sheet of uniformlydistributed glass fibers,with or without the addition of rein-forcing stranded glass yarns,and bonded with a water-resistantresinous binder.5.2 In the process of manufacture,the felt shall be impreg-nated
10、 with asphalt which shall be permitted to contain amineral stabilizer so that the individual glass fibers are coatedand the asphalt is evenly distributed throughout.5.3 The impregnated glass felt shall be surfaced with amaterial to prevent sticking in the roll.The nature and quantityof the surfacing
11、 material shall not interfere with adhesionbetween the plies of a membrane.6.Physical Properties,Dimensions,Masses,andPermissible Variations6.1 The finished product shall conform to the physicalproperties,dimensions,masses,and permissible variations asprescribed in Table 1 and Table 2.TABLE 1 Physic
12、al Properties of Asphalt Glass FeltType IVType VIBreaking strength,Amin,kN/m lbf in.:Longitudinal(with the fiber grain)7.7 4410.5 60Transverse(across the fiber grain)7.7 4410.5 60Pliability,13-mm 12-in.radius bendno failuresno failuresATo prevent the asphalt-impregnated glass felt from slipping from
13、 between thejaws of the tension testing machine,insert a thin strip of soft gasket rubberbetween the felt and each of the four jaw faces of the machine.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08
14、.04on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved Dec.15,2015.Published December 2015.Originallyapproved in 1963.Last previous edition approved in 2015 as D2178/D2178M 15.DOI:10.1520/D2178_D2178M-15A.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta
15、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 TABLE 2 Dimensions and Masses
16、of Asphalt Glass FeltAType IVType VIWidth of roll,mm in.,or as agreed between purchaser and supplier914 36 0.7%914 36 0.7%Area of roll,min,m2ft2,or as agreed between purchaser and supplier50.17 54050.17 540Net dry mass of asphalt-impregnated glass felt,min,g/m2lb 100 ft2Average of all rollsNonmineral parting agent303 6.2303 6.2Mineral parting agent342 7.0342 7.0Individual rolls293 6.0293 6.0Moisture at point of manufacture,%,maxA1.01.0Mass of desaturated glass felt,min,g/m2lb 100 ft283 1.793 1.9
