1、Designation:D228/D228M21Standard Test Methods forSampling,Testing,and Analysis of Asphalt Roll Roofing,Cap Sheets,and Shingles Used in Roofing andWaterproofing1This standard is issued under the fixed designation D228/D228M;the number immediately following the designation indicates the yearof origina
2、l adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover procedures for sampling,examination,physical te
3、sting,and analyses of asphalt-containing materials used in roofing and waterproofing.Thesematerials include but are not limited to roll roofing,cap sheets,and shingles.Any of these materials is allowed to be partiallyor fully coated,surfaced,or laminated,or a combinationthereof.1.2 The test methods
4、and procedures in this standard appearin the following order:SectionContent6Types of Roofing7Sampling8Mass and Area Determination9Selection of Representative Specimens10Moisture11Pliability12Mass Loss and Behavior on Heating13Tear Strength14Fastener Pull-Through Resistance15Preparation and Selection
5、 of Small Test Specimensfor Analyses16Analysis of Glass Felt Products17Analysis of Roofing Products with Organic Felts18Ash of Desaturated Felt19Calculation20Adjusting Back Coating Fine Mineral Matter andBack Surfacing21Report22Precision and Bias1.3 The values stated in either SI units or inch-pound
6、 unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in nonconformancewith the standard.1.4 This standard does not purport to address
7、all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in a
8、ccor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM
9、 Standards:2D95 Test Method for Water in Petroleum Products andBituminous Materials by DistillationD146/D146M Test Methods for Sampling and TestingBitumen-Saturated Felts and Woven Fabrics for Roofingand WaterproofingD225 Specification for Asphalt Shingles(Organic Felt)Sur-faced With Mineral Granule
10、s(Withdrawn 2012)3D1079 Terminology Relating to Roofing and WaterproofingD1922 Test Method for Propagation Tear Resistance ofPlastic Film and Thin Sheeting by Pendulum MethodD2178/D2178M Specification forAsphalt Glass Felt Used inRoofing and WaterproofingD2626/D2626M Specification for Asphalt-Satura
11、ted andCoated Organic Felt Base Sheet Used in RoofingD3462/D3462M Specification for Asphalt Shingles Madefrom Glass Felt and Surfaced with Mineral GranulesD3909/D3909M Specification for Asphalt Roll Roofing(Glass Felt)Surfaced With Mineral GranulesD4601/D4601M Specification for Asphalt-Coated Glass
12、Fi-ber Base Sheet Used in RoofingD4897/D4897M Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing1These test methods are under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and are the direct responsibility of SubcommitteeD08.02 on Steep Roofing Produ
13、cts and Assemblies.Current edition approved Feb.15,2021.Published February 2021.Originallyapproved in 1925.Last previous edition approved in 2019 as D228/D228M 19a.DOI:10.1520/D0228_D0228M-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servic
14、eastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-
15、2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical
16、Barriers to Trade(TBT)Committee.1D4932/D4932M Test Method for Fastener Rupture and TearResistance of Roofing and Waterproofing Sheets,RollRoofing,and ShinglesD6380/D6380M Specification for Asphalt Roll Roofing(Or-ganic Felt)F1667 Specification for Driven Fasteners:Nails,Spikes,andStaples3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in these test methods,seeTerminology D1079.3.1.2 As referenced in 15.1,“Materials of Uniform Compo-sition”designates products that are manufactured
