1、Designation:D415422Standard Performance Specification forMens and Boys Knitted and Woven Beachwear and SportsShirt Fabrics1This standard is issued under the fixed designation D4154;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers knitted and wo-ven fabrics comprised of any textile fiber or mixture of fiber
3、sused in mens and boys beachwear and sports shirts.1.2 This performance specification is not applicable toknitted and woven fabrics used for interlining and swimwear.1.3 These requirements apply to both the length and widthdirections for those properties where fabric direction is perti-nent.1.4 This
4、 standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This int
5、ernational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Co
6、mmittee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2262 Test Met
7、hod for Tearing Strength of Woven Fabricsby the Tongue(Single Rip)Method(Constant-Rate-of-Traverse Tensile Testing Machine)(Withdrawn 1995)3D2594 Test Method for Stretch Properties of Knitted FabricsHaving Low PowerD2724 Test Method for Bond Strength of Bonded,Fused,and Laminated Apparel FabricsD378
8、6 Test Method for Bursting Strength of TextileFabricsDiaphragm Bursting Strength Tester MethodD3787 Test Method for Bursting Strength of TextilesConstant-Rate-of-Traverse(CRT)Ball Burst TestD5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating
9、to Apparel(Withdrawn 2022)32.2 AATCC Test Methods:4TM8 Colorfastness to Crocking:Crockmeter MethodTM15 Colorfastness to PerspirationTM16.3 Colorfastness to Light:Xenon-ArcTM23 Colorfastness to Burnt Gas FumesTM61 Colorfastness to Laundering:AcceleratedTM96 Dimensional Changes in Laundering of Woven
10、andKnitted Textiles Except WoolTM116 Colorfastness to Crocking:Rotary Vertical Crock-meter MethodTM124 Smoothness Appearance of Fabrics After RepeatedHome LaunderingsTM132 Colorfastness to DrycleaningTM135 Dimensional Changes of Fabrics after Home Laun-deringTM172 Colorfastness to Powdered Non-chlor
11、ine Bleach inHome LaunderingTM188 Colorfastness to Sodium Hypochlorite Bleach inHome LaunderingEP1 Gray Scale for Color ChangeEP2 Gray Scale for StainingEP8 AATCC 9-Step Chromatic Transference ScaleM11 A Glossary of AATCC Standard Terminology1This performance specification is under the jurisdiction
12、of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.61 onApparel.Current edition approved Nov.1,2022.Published November 2022.Originallyapproved in 1982.Last previous edition approved in 2014 as D4154 14.DOI:10.1520/D4154-22.2For referenced ASTM standards,visit the A
13、STM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4AATCC Technical Manual,
14、available from American Association of TextileChemists and Colorists(AATCC),P.O.Box 12215,Research Triangle Park,NC27709,http:/www.aatcc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accord
15、ance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.3 Federal Standard:516 CFR,Chapter
16、 IIConsumer Product Safety CommissionSubchapter DFlammable Fabrics Act Regulations.2.4 Military Standard:6MIL-STD-105D Sampling Procedures and Tables for In-spection by AttributesNOTE1Reference to test methods in this performance specificationgive only the permanent part of the designation of ASTM,AATCC,orother test methods.The current editions of each test method cited shallprevail.3.Terminology3.1 For all terminology related to Apparel,see TerminologyD7022.3.1.1 The following terms are relevan
