1、Designation:D185609(Reapproved 2015)Standard Test Method forRecovery of Asphalt From Solution by Abson Method1This standard is issued under the fixed designation D1856;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the recovery by the Absonmethod of asphalt from a solution from a previously conductedextraction.The asp
3、halt is recovered with properties substan-tially the same as those it possessed in the bituminous mixtureand in quantities sufficient for further testing.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are provided forinformation only.1.3 This stan
4、dard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM
5、Standards:2C670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsD2172 Test Methods for Quantitative Extraction of BitumenFrom Bituminous Paving MixturesD2939 Test Methods for Emulsified Bitumens Used asProtective Coatings(Withdrawn 2012)3D4080 Specifica
6、tion for Trichloroethylene,Technical andVapor-Degreasing GradeD6368 Specification for Vapor-Degreasing Solvents Basedon normal-Propyl Bromide and Technical Grade normal-Propyl BromideE1 Specification for ASTM Liquid-in-Glass Thermometers3.Summary of Test Method3.1 The solution of solvent and asphalt
7、 from an asphalt mixextraction is distilled under prescribed conditions to a pointwhere most of the solvent has been distilled,at which timecarbon dioxide gas is introduced into the distillation process toremove all traces of the extraction solvent.The recoveredasphalt(distillation residue)can then
8、be subjected to furthertesting as required.4.Significance and Use4.1 The asphalt should be extracted from the aggregate-asphalt mixture in accordance with Method A of Test MethodsD2172(centrifuge method)as there is some experimentalevidence that the recovered asphalt may have slightly lowerpenetrati
9、on values when recovered from solutions obtainedfrom hot extraction methods.5.Apparatus5.1 Centrifuge,batch unit capable of exerting a minimumcentrifugal force of 770 times gravity or continuous unitcapable of exerting a minimum force of 3000 times gravity.5.2 Centrifuge TubesA supply of wide-mouth
10、bottles orcentrifuge tubes may be used for the batch unit.A tube asillustrated in Fig.1 has been found satisfactory for thecontinuous unit.5.3 Distillation Assembly,as shown in Fig.2,and consistingof the following items:5.3.1 Extraction FlasksTwo 250-ml,wide-mouth,heat-resistant flasks,one for disti
11、llation and the other for thereceiver.5.3.2 Glass TubingHeat-resistant glass tubing,having10-mm inside diameter and gooseneck shaped(as shown inFig.2)for connecting the flask to the condenser.5.3.3 Inlet Aeration Tube,4at least 180 mm in length,havinga 6-mm outside diameter with a 10-mm bulb carryin
12、g sixstaggered side holes approximately 1.5 mm in diameter.5.3.4 Electric Heating Mantle,with variable transformer,oilbath,or fluidized sand bath,to fit a 250-ml flask.5.3.5 Water-Jacketed Condenser,Allihn type,with 200-mmminimum jacket length or equivalent.1This method is under the jurisdiction of
13、ASTM Committee D04 on Road andPaving Materials and is the direct responsibility of Subcommittee D04.25 onAnalysis of Asphalt Mixtures.Current edition approved Jan.1,2015.Published February 2015.Originallyapproved in 1961.Last previous edition approved in 2009 as D1856 09.DOI:10.1520/D1856-09R15.2For
14、 referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced o
15、nwww.astm.org.4The sole source of supply of the apparatus known to the committee at this timeis Inlet Aeration Tube,Part No.226,available from Wm.A.Sales,Ltd.,419Harvester Court,Wheeling,Ill.60090;request Part No.226.If you are aware ofalternative suppliers,please provide this information to ASTM In
16、ternationalHeadquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,1which you may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 FIG.1 Centrifuge Tube ExampleFIG.2 Distillation Assembly for Bitumen RecoveryD1856 09(2015)2 5.3.6 ThermometerAnASTM Low Distillation Thermom-eter 7E or 7F,as specified,having a range from 2 to 300C or30 to 580F,respectively,and conforming to t
