1、Designation:D2846/D2846M17An American National StandardStandard Specification forChlorinated Poly(Vinyl Chloride)(CPVC)Plastic Hot-andCold-Water Distribution Systems1This standard is issued under the fixed designation D2846/D2846M;the number immediately following the designation indicates theyear of
2、 original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of
3、 Defense.1.Scope*1.1 This specification covers requirements,test methods,assembly,and methods of marking for chlorinated poly(vinylchloride)plastic hot-and cold-water distribution system com-ponents made in one standard dimension ratio and intended forwater service up to and including 180F(82C).Thes
4、e com-ponents comprise pipe and tubing,socket-type fittings,streetfittings,plastic-to-metal transition fittings,solvent cements,and adhesives.Requirements and methods of test are includedfor materials,workmanship,dimensions and tolerances,hydro-static sustained pressure strength,and thermocycling re
5、sis-tance.The components covered by this specification areintended for use in residential and commercial,hot and cold,potable water distribution systems.1.2 The products covered by this specification are intendedfor use with the distribution of pressurized liquids only,whichare chemically compatible
6、 with the piping materials.Due toinherent hazards associated with testing components and sys-tems with compressed air or other compressed gases somemanufacturers do not allow pneumatic testing of their products.Consult with specific product/component manufacturers fortheir specific testing procedure
7、s prior to pneumatic testing.NOTE1Pressurized(compressed)air or other compressed gasescontain large amounts of stored energy which present serious safteyhazards should a system fail for any reason.1.3 The text of this specification references notes,footnotes,and appendixes which provide explanatory
8、material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;there
9、fore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.NOTE2Suggested hydrostatic design stresses and hydrostatic pressureratings for pipe,tubing,and fittings are listed in Appendix X1.Design andinstallation consid
10、erations are discussed in Appendix X2.An optionalperformance qualification and an in-plant quality control program arerecommended in Appendix X3.1.5 The following safety hazards caveat pertains only to thetest method portion,Sections 9 and 10,of this specification:This standard does not purport to a
11、ddress all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.1.6 This international standard was developed in accor-dance
12、with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:
13、2D1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)Compoun
14、dsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2855 Practice for the Two-Step(Primer and Solvent Ce-ment)Method of Joining Poly(Vinyl Chloride)(PVC)orChlorinated Poly(Vinyl Chloride)(CPVC)Pipe andPiping Components with Tapered SocketsD2444 Test Method for Determin
15、ation of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.61 on Water.Current edition approved July 1,2017.Publis
16、hed July 2017.Originally approvedin 1969.Last previous edition approved in 2014 as D2846/D2846M 141.DOI:10.1520/D2846_D2846M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Consh
