1、Manual of PetroleumMeasurement StandardsChapter 11Physical Properties DataSection 1Temperature and Pressure Volume Correction Factors for Generalized Crude Oils,Refined Products,and Lubricating OilsAdjunct to:ASTM D 1250-04 and IP 200/04MAY 2004ADDENDUM 1,SEPTEMBER 2007 ADDENDUM 2,MAY 2019ASTM Stock
2、#:ADJD1250-A1A2-E-PDFSPECIAL NOTESAPI publications necessarily address problems of a general nature.With respect to particularcircumstances,local,state,and federal laws and regulations should be reviewed.Neither API nor any of APIs employees,subcontractors,consultants,committees,or otherassignees ma
3、ke any warranty or representation,either express or implied,with respect to theaccuracy,completeness,or usefulness of the information contained herein,or assume anyliability or responsibility for any use,or the results of such use,of any information or processdisclosed in this publication.Neither AP
4、I nor any of APIs employees,subcontractors,con-sultants,or other assignees represent that use of this publication would not infringe upon pri-vately owned rights.API publications may be used by anyone desiring to do so.Every effort has been made bythe Institute to assure the accuracy and reliability
5、 of the data contained in them;however,theInstitute makes no representation,warranty,or guarantee in connection with this publicationand hereby expressly disclaims any liability or responsibility for loss or damage resultingfrom its use or for the violation of any authorities having jurisdiction wit
6、h which this publi-cation may conflict.API publications are published to facilitate the broad availability of proven,sound engineer-ing and operating practices.These publications are not intended to obviate the need forapplying sound engineering judgment regarding when and where these publications s
7、houldbe utilized.The formulation and publication of API publications is not intended in any wayto inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the markingrequirements of an API standard is solely responsible for complying with all
8、the applicablerequirements of that standard.API does not represent,warrant,or guarantee that such prod-ucts do in fact conform to the applicable API standard.All?of?or?200 Massachusetts Avenue?Suite 1100,?1.Copyright 2007 American Petroleum InstituteiiFOREWORDNothing contained in any API publication
9、 is to be construed as granting any right,by impli-cation or otherwise,for the manufacture,sale,or use of any method,apparatus,or productcovered by letters patent.Neither should anything contained in the publication be construedas insuring anyone against liability for infringement of letters patent.
10、This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API Stan-dard.Questions concerning the interpretation of the content of this publication or comments and questions concerning th
11、e procedures under which this publication was developed should be directed in writing to the Director of Standards,American Petroleum Institute,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Requests for permission to reproduce or translate all or any part of the material published herei
12、n should also be addressed to the director.Generally,API Standards are reviewed and revised,reaffirmed,or withdrawn at least every five years.A one-time extension of up to two years may be added to this review cycle.Status of the publication can be ascertained from the API Standards Department,telep
13、hone(202)682-8000.A catalog of API publications and materials is published annually and updatedquarterly by API,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Suggested revisions are invited and should be submitted to the Standards and Publications Department,API,200 Massachusetts Avenue
14、,NW,Suite 1100,Washington,DC 20001,standardsapi.org.iiiivCONTENTS Section 1 Temperature and Pressure Volume Correction Factors for Generalized Crude Oils,Refined Products,and Lubricating Oils.1 11.1.0 Implementation Guidelines.1 11.1.1 Introduction&History.1 11.1.1.1 Early Temperature and Pressure C
15、orrection Tables.1 11.1.1.2 1952 Temperature Correction Tables.1 11.1.1.3 1980 Temperature Correction Tables.2 11.1.1.4 1981 Pressure Correction Tables.3 11.1.1.5 Changes to Previous Standards.3 11.1.1.6 Customary Temperature&Pressure Correction Tables.6 11.1.2 Purpose.6 11.1.2.1 Significance.6 11.1
16、.2.2 Scope.6 11.1.2.3 Temperature,Pressure,and Density Limits.7 11.1.2.4 Classification of Liquids.10 11.1.2.4.1 Crude Oil.10 11.1.2.4.2 Refined Products.10 11.1.2.4.3 Lubricating Oils.11 11.1.2.4.4 Special Applications.11 11.1.2.5 Application of Tables to Specific Substances.12 11.1.2.5.1 Waxy Crudes.12 11.1.2.5.2 Natural and Drip Gasolines.12 11.1.2.5.3 LPG and NGL.12 11.1.2.5.4 LNG.12 11.1.2.5.5 Ethylene and Propylene.12 11.1.2.5.6 Butadiene.12 11.1.2.5.7 Cyclohexane and Aromatics.12 11.1.2.5
