1、Designation:D1670/D1670M11(Reapproved 2018)Standard Test Method forFailure End Point in Accelerated and Outdoor Weathering ofBituminous Materials1This standard is issued under the fixed designation D1670/D1670M;the number immediately following the designation indicates theyear of original adoption o
2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the use of a spark generatingapparatus for determination of f
3、ailure due to cracking ofbituminous materials undergoing accelerated or outdoor weath-ering on electrically conductive backings.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore
4、,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to esta
5、blish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles f
6、or theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1435 Practice for Outdoor Weathering of PlasticsD1669/D1669M Practice for Preparation of Test Panels for
7、Accelerated and Outdoor Weathering of Bituminous Coat-ingsD4798/D4798M Practice for Accelerated Weathering TestConditions and Procedures for Bituminous Materials(Xenon-Arc Method)D4799/D4799M Practice for Accelerated Weathering TestConditions and Procedures for Bituminous Materials(Fluorescent UV,Wa
8、ter Spray,and Condensation Method)3.Summary of Test Method3.1 Dry,weathered,bituminous-coated test panels aregrounded and a feeler electrode is passed over the back of alinagraphic or ultra high sensitivity thermal fax paper placed onthe bituminous surface with the emulsion side down.Photo-copies ar
9、e made of the front side of the paper on which thespots caused by the sparks appear.The photographs arecovered with an acrylic grid and the number of squarescontaining the spark records are counted and reported.Spark-ing in 26 or more grid squares is representative of failure.4.Significance and Use4
10、.1 The extent of cracking or pitting of bituminous films isa measure of the extent of deterioration due to weathering.Failure due to cracking is more accurately determined electri-cally than visually.4.2 Failure determined by this test method will depend notonly on the characteristics of the bitumin
11、ous material and theextent of weathering,but also on the film thickness,and theamount and type of mineral filler present.4.3 Tests on a similar material of known weathering char-acteristics(a control)exposed at the same time as the testmaterial is strongly recommended as a check on the validity ofth
12、e test results.5.Apparatus5.1 Any Spark-Generating Apparatus3Fig.1 is an ex-ample of an acceptable configuration for the test feeler.Otherconfigurations are not prohibited,subject to the followingconditions:1This test method is under the jurisdiction ofASTM Committee D08 on Roofingand Waterproofing
13、and is the direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved Nov.1,2018.Published December 2018.Originallyapproved in 1959.Last previous edition approved in 2011 as D1670/D1670M 11.DOI:10.1520/D1670_D1670M-11R18.2For referenced ASTM standar
14、ds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The sole source of supply of the apparatus known to the committee at this timeis Electrotechn
15、ic Model BD-40B Spark Generator,available from Electro-TechnicProducts Co.,4642 N.Ravenswood Ave.,Chicago,IL 60642.If you are aware ofalternative suppliers,please provide this information to ASTM Headquarters.Yourcomments will receive careful consideration at a meeting of the responsibletechnical co
16、mmittee,1which you may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.1.1 The cross-dimension of the wire loop is
