1、Designation:D1668/D1668M97a(Reapproved 2014)1Standard Specification forGlass Fabrics(Woven and Treated)for Roofing andWaterproofing1This standard is issued under the fixed designation D1668/D1668M;the number immediately following the designation indicates theyear of original adoption or,in the case
2、of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.This specification replac
3、es Federal Specification HH-C-466.1NOTEUnits information was editorially corrected in May 2014.1.Scope1.1 This specification covers finished treated(coated)woven-glass fabrics coated with either asphalt,coal-tar pitch oran organic resin compatible with the roofing,waterproofing,orother usage as spec
4、ified by the purchaser.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in n
5、on-conformancewith the standard.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing andWaterproofingD579 Specification for Greige Woven Glass FabricsD1079 Terminology Relating
6、to Roofing and WaterproofingD3775 Test Method for Warp(End)and Filling(Pick)Countof Woven FabricsD3776 Test Methods for Mass Per Unit Area(Weight)ofFabric3.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to Terminology D123 or D1079.4.Classification of Fabric Treat
7、ments with GenerallyApplicable Usage4.1 Type I,Asphalt TreatedType I is suitable for use withall asphalts and asphalt based compounds.4.2 Type II,Coal Tar Pitch TreatedType II is suitable foruse with all coal tar pitches and coal tar pitch based compounds(Note 1).4.3 Type III,Organic Resin TreatedTh
8、e purchaser andsupplier shall agree on an organic resin that is compatible withor is suitable for,or both,the plying liquid plying materialseither specified or to be used.This organic resin shall not bewater soluble.NOTE1In some instances the purchaser may specify the use of TypesI or II for systems
9、 using other than coal tar bitumens or asphalt.5.Materials and Manufacture5.1 The untreated(greige)scrim(open basket weave)orleno(locked weave)fabrics shall conform to the requirementsas specified in Table 1.5.2 In the process of manufacture,the fibers of the untreatedglass fabric shall be thoroughl
10、y and uniformly coated usingequipment which,in combination,handles the fabric and usesa machine speed in a total process that will not injure or distortthe weave of the fabric.5.3 Glass fabric is usually woven in nominal widths of 0.91,1.83 and 2.74 m 36,72 and 108 in.by the weaving mills.Extra warp
11、(the length of the fabric)threads are included in1.83 and 2.74-m 72 and 108-in.wide fabrics to obtainincremental fabric roll widths of 0.91 m 36 in.These extrawarp threads with a slitting space between each set(a set oftwo)of bunched warp threads create a duplicate or“dupe”selvedge with a“brush”edge
12、 created by the cut fill threadsinstead of the usually wrapped fill threads seen in a smoothselvedge.This type of fabric selvedge edge is,and has been,anacceptable fabric design(pattern)in both the weaving andconstruction industry.1This specification is under the jurisdiction of ASTM Committee D08 o
13、nRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved May 1,2014.Published May 2014.Originallyapproved in 1959.Last previous edition approved in 2006 as D1668 97a(2006).DOI:10.1520/D1668_D1668M-97AR1
14、4E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C70
15、0,West Conshohocken,PA 19428-2959.United States1 5.4 Brush edge of the“dupe”selvedge is not to be includedin the measurement of the finished roll width.5.5 The purchaser may specify widths of more than or lessthan 0.91 m 36 in.These widths can be furnished at themanufacturers option.6.Physical Prope
16、rties6.1 Coated FabricThe coated fabric shall conform to therequirements as specified in Table 2.The coated fabric shall notflake at 0C 32F when flexed 180 over 25 mm 1 in.outside diameter mandrel and then immediately reversed.6.2 Finished FabricThe finished fabric shall be capable ofretaining its original shape and shall consist of a right angleweave set pattern without bunching either the warp or fillthreads when unrolled during normal handling.There shall beno sticking at temperatures of 10C
