收藏 分享(赏)

ASTM_D_1725_-_12_2019.pdf

上传人:益****师 文档编号:182560 上传时间:2023-03-04 格式:PDF 页数:3 大小:77.63KB
下载 相关 举报
ASTM_D_1725_-_12_2019.pdf_第1页
第1页 / 共3页
ASTM_D_1725_-_12_2019.pdf_第2页
第2页 / 共3页
ASTM_D_1725_-_12_2019.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D172512(Reapproved 2019)Standard Practice forPreparing Resin Solutions for Viscosity Measurement byBubble Time Method1This standard is issued under the fixed designation D1725;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisi

2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice provides instructions for preparing resinsolutions viscosity measurement by bubble time method

3、.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-

4、priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statements,see Section 7.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establishe

5、d in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D154 Guide for Testing of Varnishes(Withdrawn 2018)3D1545 Test Method fo

6、r Viscosity of Transparent Liquids byBubble Time MethodD6440 Terminology Relating to Hydrocarbon ResinsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 Other Document:OSHA Regulations,29 CFR,paragraphs 19.10.1000 and1910.120043.Terminology3.1 For de

7、finitions related to hydrocarbon resins see Termi-nology D6440.4.Summary of Practice4.1 Solid resins are dissolved in organic solvents by cold-cut or hot-cut methods in the laboratory.The viscosity of suchprepared solutions,or of commercial solutions of resins is thendetermined by the bubble time me

8、thod(Test Method D1545).The bubble seconds are approximately equal to stokes.5.Apparatus5.1 Bath,constant-temperature,consisting of a cylindricalglass jar of about 5-gal capacity,or an aquarium tank withcontrols capable of maintaining the temperature at 25 6 0.1Cwith water as the bath medium.5.2 Bot

9、tles,225-mL(8-oz),wide-mouth,screw cap.5.3 Cellophane,sheet,cut into 102 or 127-mm(4 or 5-in.)squares.5.4 Corks,No.2 short taper,to fit viscosity tubes.5.5 Holder for Viscosity Tubes,preferably a mechanicalholder5with rack and pinion for inverting the tubes.The holdershould be checked with a small l

10、evel and T-square to makecertain it holds the tubes in an exact vertical position afterbeing placed in the constant-temperature bath.5.6 Bottle Shaker,preferably one which will give end-over-end agitation.1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Mat

11、erials,and Applications and is the direct responsibility ofSubcommittee D01.33 on Polymers and Resins.Current edition approved June 1,2019.Published June 2019.Originallyapproved in 1960.Last previous edition approved in 2012 as D1725 12.DOI:10.1520/D172512R19.2For referenced ASTM standards,visit the

12、 ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from U.S.Go

13、vernment Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.5Suitable mechanical viscosity tube holders are available from various labora-tory supply companies.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West

14、 Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade

15、Organization Technical Barriers to Trade(TBT)Committee.1 5.7 Timing Device,such as a stopwatch or electric stopclock capable of being read to a precision of 0.1 s.5.8 Viscosity Tubes,of clear glass and flat bottoms,having10.65 6 0.025-mm inside diameter and 114 6 1-mm outsidelength.Plainly legible l

16、ines shall be located on the tubes asfollows:27 0.5 mm100 0.5 mm108 0.5 mmAll distances shall be measured from the bottom outside ofthe tube.The distance between the first and second lines shallbe 73 6 0.5 mm.6.Solvent6.1 The solvent used should be mutually agreed uponbetween the purchaser and the manufacturer.Toluene,xylene,mineral spirits,alcohols,etc.,are used for the preparation ofsolutions of resins.For a given resin,the viscosity obtainedwill depend on the solvent used.In case of dispute,b

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2