1、Designation:D362485a(Reapproved 2022)Standard Test Method forLow Concentrations of Mercury in Paint by AtomicAbsorption Spectroscopy1This standard is issued under the fixed designation D3624;the number immediately following the designation indicates the year oforiginal adoption or,in the case of rev
2、ision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method cov
3、ers the determination of the contentof mercury in the range between 10 and 1000 ppm(mg/kg)present in liquid coatings,coatings vehicles,or in dried filmsobtained from previously coated substrates.There is no reasonto believe that higher levels could not be determined by thistest method,provided that
4、appropriate dilutions and adjust-ments in specimen size and reagent quantities are made.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmenta
5、l practices and deter-mine the applicability of regulatory limitations prior to use.Specific hazard statements are given in Section 7 and 9.1.1.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on P
6、rinciples for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent Water3.Summary of Test Method3.1 The sample of liquid coating
7、or dried film is weighedinto a polytetrafluoroethylene(PTFE)-lined acid decomposi-tion vessel and digested at an elevated temperature usingsulfuric and nitric acids.Use of a sealed acid decompositionvessel prevents loss of mercury during the digestion.Thedigested sample is diluted to a known volume
8、with water andthe concentration of mercury is determined using a cold-vapor,atomic absorption technique.4.Significance and Use4.1 The permissible level of heavy metals in certain coat-ings is specified by governmental regulatory agencies.This testmethod provides a fully documented procedure for dete
9、rmininglow concentrations of mercury present in both water andsolvent-reducible coatings to determine compliance.5.Apparatus5.1 Atomic Absorption SpectrophotometerAny commer-cial instrument having an open sample presentation area inwhich to mount the absorption cell or an instrument designedspecific
10、ally for the measurement of mercury using the coldvapor technique.5.2 Recorder,0 to 10 mV.5.3 Mercury Source Lamp.5.4 Absorption CellStandard spectrophotometer cells 100mm long,having quartz end windows may be used.Prior touse,the cell must be positioned in the optical path of thespectrophotometer a
11、nd held in place by suitable clamps orstraps.The cell should be carefully aligned both vertically andhorizontally to give the maximum transmittance.5.5 Reduction VesselCylindrical gas washing bottle,250-mL,equipped with a coarse(40 to 60-m)fritted glass inlettube and a standard-taper glass stopper.P
12、olyethylene or poly-(vinyl chloride)tubing may be used for connecting the reduc-tion vessel to the absorption cell.5.6 Flowmeter,capable of measuring a gas flow of 1 L/min.5.7 Drying TubeApproximately 150 by 20-mm(6 by34-in.)glass tube filled with magnesium perchlorate.The tubeshould be filled each
13、day that it is in use,and the Mg(ClO4)2should be replaced whenever it becomes saturated(carefullyobserve after each analysis).NOTE1Use of an indicator desiccant at the exit end of the tube willmake this observation easier.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand
14、Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved June 1,2022.Published June 2022.Originallyapproved in 1977.Last previous edition approved in 2015 as D3624 85a(2015).DOI:10.1
15、520/D3624-85AR22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Driv
16、e,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.8 Water Vapor TrapA second 250-mL gas washingbottle(the same as used for the reduction vessel).If preferred,a 250-mL Erlenme
