收藏 分享(赏)

ASTM_D_1743_-_13.pdf

上传人:益****师 文档编号:183309 上传时间:2023-03-04 格式:PDF 页数:12 大小:430.51KB
下载 相关 举报
ASTM_D_1743_-_13.pdf_第1页
第1页 / 共12页
ASTM_D_1743_-_13.pdf_第2页
第2页 / 共12页
ASTM_D_1743_-_13.pdf_第3页
第3页 / 共12页
ASTM_D_1743_-_13.pdf_第4页
第4页 / 共12页
ASTM_D_1743_-_13.pdf_第5页
第5页 / 共12页
ASTM_D_1743_-_13.pdf_第6页
第6页 / 共12页
亲,该文档总共12页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D174313Standard Test Method forDetermining Corrosion Preventive Properties of LubricatingGreases1This standard is issued under the fixed designation D1743;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last r

2、evision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination o

3、f the corro-sion preventive properties of greases using grease-lubricatedtapered roller bearings stored under wet conditions.This testmethod is based on CRC Technique L 412that shows correla-tions between laboratory results and service for grease lubri-cated aircraft wheel bearings.1.2 Apparatus Dim

4、ensionsThe values stated in SI unitsare to be regarded as standard.The values given in parenthesesare for information only.1.3 All Other ValuesThe values stated in SI units are to beregarded as standard.No other units of measurement areincluded in this standard.1.4 This standard does not purport to

5、address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3D1193 Specific

6、ation for Reagent WaterD5969 Test Method for Corrosion-Preventive Properties ofLubricating Greases in Presence of Dilute Synthetic SeaWater Environments3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 corrosion,nthe chemical or electrochemical reac-tion between a material,usuall

7、y a metal,and its environmentthat produces a deterioration of the material and its properties.3.1.1.1 DiscussionIn this test method,corrosion is mani-fested by red rust or black stains on the bearing race.Stains,through which the underlying metal surface is still visible,arenot considered corrosion

8、in Test Method D1743 and shall beignored.4.Summary of Test Method4.1 New,cleaned,and lubricated bearings are run under alight thrust load for 60 6 3 s to distribute the lubricant in apattern that might be found in service.The bearings areexposed to water,then stored for 48 6 0.5 h at 52 6 1C(1256 2F

9、)and 100%relative humidity.After cleaning,thebearing cups are examined for evidence of corrosion.5.Significance and Use5.1 This test method differentiates the relative corrosion-preventive capabilities of lubricating greases under the condi-tions of the test.6.Apparatus6.1 BearingsTimken bearing con

10、e and roller assemblyLM11949,and cup LM11910.4,56.2 Motor,1750 6 50-rpm speed,115hp(min).6.3 Bearing Holder,consists of a 1 6 0.10 kg weight,upperand lower plastic collars for the bearing cone(Parts A and B),a metal screw,and a plastic collar for the cup(Part C).(See Fig.1.)6.4 Plastic Test Jar,as s

11、hown in Fig.2.6.5 Run-in Stand,as shown in Fig.3.6.6 Spindle/Thrust Loading Device,as shown in Fig.4.(SeeTable 1 for metric equivalents.)1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee

12、D02.G0.06 on Functional Tests-Contamination.Current edition approved May 1,2013.Published May 2013.Originallyapproved in 1960.Last previous edition approved in 2010 as D1743 10.DOI:10.1520/D1743-13.2“Research Technique for Determining Rust-Preventive Properties of Lubricat-ing Greases in the Presenc

13、e of Free Water,”L-41-957,undated,CoordinatingResearch Council,Inc.,219 Perimeter Center Parkway,Atlanta,GA 30346.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the sta

14、ndards Document Summary page onthe ASTM website.4The sole source of supply of the apparatus known to the committee at this timeis The Timken Co.,Canton,OH 44706.5If you are aware of alternative suppliers,please provide this information toASTM International Headquarters.Your comments will receive car

15、eful consider-ation at a meeting of the responsible technical committee,1which you may attend.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 KEYDESCRIPTIONQUANTITY1PISTON12

16、O RING13WEIGHT14UPPER FLANGE15LOWER FLANGE1614 20 1-14FILLISTER HD.MACH.SCREW S.S.17O RING18BEARING HOLDER19PLASTIC JAR110O RING1FIG.1 Bearing Holder AssemblyD1743 132 6.7 Mechanical Grease Packer,as shown in Fig.5 and Fig.6.6.8 Pliers,5,6as shown in Fig.7.6.9 Syringe,of at least 100-mL volume and with a needle ofat least 16 gage and a minimum length of 100 mm(4 in.).6.10 Timer,capable of measuring a 60 6 3-s interval.6.11 OvenA laboratory oven,essentially free of vibration,capable of maintainin

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2