1、Designation:D 1527 99e1An American National StandardStandard Specification forAcrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe,Schedules 40 and 801This standard is issued under the fixed designation D 1527;the number immediately following the designation indicates the year oforiginal adoption or,in
2、the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.e1NOTEKeywords were
3、 editorially added in November 2003.1.Scope1.1 This specification covers acrylonitrile-butadienestyrene(ABS)pipe produced by single extrusion or simultaneousmultiple coextrusion,in Schedule 40 and 80 sizes and pressure-rated for water(see Appendix).Included are criteria forclassifying ABS plastic pi
4、pe materials and ABS plastic pipe,asystem of nomenclature forABS plastic pipe,and requirementsand test methods for materials,workmanship,dimensions,sustained pressure,burst pressure,and extrusion quality.Meth-ods of marking are also given.1.2 The products covered by this specification are intendedfo
5、r use with the distribution of pressurized liquids only,whichare chemically compatible with the piping materials.Due toinherent hazards associated with testing components and sys-tems with compressed air or other compressed gases somemanufacturers do not allow pneumatic testing of their products.Con
6、sult with specific product/component manufacturers fortheir specific testing procedures prior to pneumatic testing.NOTE1Pressurized(compressed)air or other compressed gasescontain large amounts of stored energy which present serious safteyhazards should a system fail for any reason.1.3 The text of t
7、his specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The values stated in inch-pound units are to be regardedas the standard.The va
8、lues given in parentheses are providedfor information purposes only.1.5 The following safety hazards caveat pertains only to thetest method portion,Section 7,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibil
9、ity of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:D 618 Practice for Conditioning Plastics for Testing2D 1598 Test Method for Time-to-Failure of Plastic
10、PipeUnder Constant Internal Pressure3D 1599 Test Method for Short-Time Hydraulic Failure Pres-sure of Plastic Pipe,Tubing,and Fittings3D 1600 Terminology for Abbreviated Terms Relating toPlastics2D 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and Fittings3D 2837 Test Method for
11、 Obtaining Hydrostatic DesignBasis for Thermoplastic Pipe Materials3D 3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene(ABS)Compounds for Pipe and Fittings4F 412 Terminology Relating to Plastic Piping Systems32.2Federal Standard:Fed.Std.No.123 Marking for Shipments(Civil Agencies)52.3Mili
12、tary Standard:MIL-STD-129 Marking for Shipment and Storage52.4NSF Standards:Standard No.14 for Plastic Piping Components and RelatedMaterials6Standard No.61 for Drinking Water System ComponentsHealth Effects63.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F 412.Abbreviati
13、ons are in accordance with Terminol-ogy D 1600,unless otherwise indicated.The abbreviation foracrylonitrile-butadiene-styrene plastic is ABS.3.2 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction ofASTM Committee F-17 on PlasticPiping Systems and is the dire
14、ct responsibility of Subcommittee F17.61 on Water.Current edition approved May 10,1999.Published July 1999.Originallypublished as D 1527 58.Last previous edition D 1527 96a.2Annual Book of ASTM Standards,Vol 08.01.3Annual Book of ASTM Standards,Vol 08.04.4Annual Book of ASTM Standards,Vol 08.02.5Ava
15、ilable from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.6Available from the National Sanitation Foundation,P.O.Box 1468,Ann Arbor,MI 48106.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,U
16、nited States.3.2.1 acrylonitrile-butadiene-styrene(ABS)pipe and fittingplasticsplastics containing polymers or blends of polymers,or both,in which the minimum butadiene content is 6%,theminimum acrylonitrile content is 15%,the minimum styreneor substituted styrene content,or both,is 15%,and themaximum content of all other monomers is not more than 5%,and lubricants,stabilizers,and colorants.3.2.2 hydrostatic design stressthe estimated maximumtensile stress the material is capable of withstanding
