1、Designation:D155521Standard Test Method forCalculation of Volume and Weight of Industrial AromaticHydrocarbons and Cyclohexane1This standard is issued under the fixed designation D1555;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,
2、the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This standard is for use i
3、n calculating the weight andvolume of benzene,toluene,mixed xylenes,styrene,orthoxylene,meta-xylene,para-xylene,cumene,ethylbenzene,300 to 350F and 350 to 400F aromatic hydrocarbons,andcyclohexane.A method is given for calculating the volume ata desired temperature tbF from an observed volume at toF
4、.Table 1 lists the density in Vacuo at 60F for chemicals used todevelop the relationship.Densities(or weights)“in vacuo”represent the true density(or weight)if measured in a vacuumwithout the buoyancy effect of air acting on the liquid.It isrepresentative of the actual amount of product present.Dens
5、i-ties(or weights)“in air”represent what would actually bemeasured on a scale.The difference is on the order of 0.13%.Modern densitometers measure density in vacuo and theASTM recommends the use of in vacuo densities(or weights).1.2 The values stated in inch-pound units are to be regardedas standard
6、.No other units of measurement are included in thisstandard.1.2.1 A complete SI unit companion standard has beendeveloped in Test Method D1555M.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard
7、to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Princ
8、iples for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1217 Test Method for Density and Relative Density(Spe-cific Gravity)of Liquids by Bingham Pycnome
9、terD1555M Test Method for Calculation of Volume and Weightof Industrial Aromatic Hydrocarbons and CyclohexaneMetricD3505 Test Method for Density or Relative Density of PureLiquid ChemicalsD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density Meter2.2 Other Docum
10、ents:American Petroleum Society Research Project 443Patterson,J.B.,and Morris,E.C.Metrologia,31,1994,pp.277-288NSRDS-NIST 75-121 TRC Thermodynamic TablesHydrocarbons,Supplement No.121,April 30,200143.Significance and Use3.1 This test method is suitable for use in calculatingweights and volumes of th
11、e products outlined in Section 1.Theinformation presented in this method can be used for deter-mining quantities of the above-stated aromatic hydrocarbons intanks,shipping containers,etc.4.Basic Data4.1 Densities of materials should be determined by mea-surement(see Section 7).Densities of pure mate
12、rials at 60Fmay be estimated from densities furnished by NSRDS-NIST75-121(National Standard Reference Data SeriesNationalInstitute of Standards and Technology).1This test method is under the jurisdiction of ASTM Committee D16 onAromatic,Industrial,Specialty and Related Chemicals and is the direct re
13、sponsi-bility of Subcommittee D16.01 on Benzene,Toluene,Xylenes,Cyclohexane andTheir Derivatives.Current edition approved July 1,2021.Published August 2021.Originallyapproved in 1957.Last previous edition approved in 2016 as D1555 16.DOI:10.1520/D1555-21.2For referenced ASTM standards,visit the ASTM
14、 website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3“Selected Values of Properties of Hydrocarbons and Related Compounds,”prepared by American Petroleum Institute
15、 Research Project 44 at the ChemicalThermodynamics Center,Department of Chemistry,Texas A&M,College Station,TX.4Available from National Institute of Standards and Technology(NIST),100Bureau Dr.,Stop 1070,Gaithersburg,MD 20899-1070,http:/www.nist.gov.Copyright ASTM International,100 Barr Harbor Drive
16、,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.2 The VCF(Volume Correction Factor)equations pro-vided below were derived from the Volume Correction Tablespresented in the p
