收藏 分享(赏)

ASTM_E_2819_-_11_2015.pdf

上传人:益****师 文档编号:183662 上传时间:2023-03-04 格式:PDF 页数:26 大小:451.48KB
下载 相关 举报
ASTM_E_2819_-_11_2015.pdf_第1页
第1页 / 共26页
ASTM_E_2819_-_11_2015.pdf_第2页
第2页 / 共26页
ASTM_E_2819_-_11_2015.pdf_第3页
第3页 / 共26页
ASTM_E_2819_-_11_2015.pdf_第4页
第4页 / 共26页
ASTM_E_2819_-_11_2015.pdf_第5页
第5页 / 共26页
ASTM_E_2819_-_11_2015.pdf_第6页
第6页 / 共26页
亲,该文档总共26页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:E281911(Reapproved 2015)An American National StandardStandard Practice forSingle-and Multi-Level Continuous Sampling of a Stream ofProduct by Attributes Indexed by AQL1This standard is issued under the fixed designation E2819;the number immediately following the designation indicates the

2、 year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice establishes tables and procedures forapplyin

3、g five different types of continuous sampling plans forinspection by attributes using MIL-STD-1235B as a basis forsampling a steady stream of lots indexed by AQL.1.2 This practice provides the sampling plans of MIL-STD-1235B in ASTM format for use by ASTM committees andothers.It recognizes the conti

4、nuing usage of MIL-STD-1235Bin industries supported by ASTM.Most of the original text inMIL-STD-1235B is preserved in Sections 6 10 of thispractice.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this stand

5、ard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E456 Terminology Relating to Quality and StatisticsE1994 Practice for Use of Process Oriented AOQL andLTPD Sampling PlansE2234 P

6、ractice for Sampling a Stream of Product by Attri-butes Indexed by AQL2.2 Military Standards:3MIL-STD-1235A1 Functional Curves of the ContinuousSampling PlansMIL-STD-1235B Single-and Multi-Level Continuous Sam-pling for Attributes3.Terminology3.1 Definitions:3.1.1 For a more extensive list of terms

7、in E11 standards seeTerminology E456.3.1.2 acceptance quality limit(AQL),nquality limit that isthe worst tolerable process average when a continuing series oflots is submitted for acceptance sampling.E22343.1.3 average outgoing quality(AOQ),nthe average per-cent defective of outgoing product includi

8、ng all accepted lotsor batches after any defectives found in them are replaced byacceptable units,plus all lots or batches which are not acceptedafter such lots or batches have been effectively 100%in-spected and all defective units replaced by acceptable units.E19943.1.4 average outgoing quality li

9、mit(AOQL),nthe maxi-mum AOQ for a given acceptance sampling plan for allpossible incoming percentages defective for the process.E19943.1.5 continuous sampling inspection,na method of sam-pling a stream of product in order of production where thesampling frequency is adjusted based on ongoing inspect

10、ionresults.3.1.5.1 DiscussionOnly those units of product found bythe inspector or screening crew to be nonconforming arerejected.The rest of production,uninspected units as well asunits found to be conforming,is allowed to continue down theproduction line as conforming material.3.1.6 critical defect

11、,na defect that judgment and experi-ence indicate would result in hazardous or unsafe conditionsfor individuals using,maintaining,or depending upon theproduct,or a defect that judgment and experience indicate islikely to prevent performance of the function of a major enditem.E22343.1.7 critical defe

12、ctive,na unit of product which containsone or more critical defects and may also contain major andminor,or both,defects.E22343.1.8 defect,nany nonconformance of the unit of productwith specified requirements.E22343.1.9 inspection,nthe process of measuring,examining,testing,or otherwise comparing the

13、 unit of product with therequirements.E22341This practice is under the jurisdiction ofASTM Committee E11 on Quality andStatistics and is the direct responsibility of Subcommittee E11.30 on StatisticalQuality Control.Current edition approved May 15,2015.Published June 2015.Originallyapproved in 2011.

14、Last previous edition approved in 2011 as E2819 11.DOI:10.1520/E2819-11R15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM

15、 website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.10 inspection by attributes,ninspe

16、ction whereby ei-ther the unit of product is classified simply as defective ornon-defective,or the number of defects in the unit of productis counted,with respect to a given requirement or set ofrequirements.E22343.1.11 major defect,na defect,other than critical,that islikely to result in failure,or to reduce materially the usabilityof the unit of product for its intended purpose.E22343.1.12 major defective,na unit of product which containsone or more major defects,and may also contain minor def

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2