1、Designation:D177796(Reapproved 2015)Standard Test Method forThickness of Textile Materials1This standard is issued under the fixed designation D1777;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number i
2、n parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the measurement of the thick-ness of most textile materials.1.2 This test method applies to most fabrics includingwoven fab
3、rics,air bag fabrics,blankets,napped fabrics,knittedfabrics,layered fabrics,and pile fabrics.The fabrics may beuntreated,heavily sized,coated,resin-treated,or otherwisetreated.Instructions are provided for testing thickness,exceptas provided for in another standard such as listed in Section 2.1.3 Th
4、e values stated in SI units are to be regarded as thestandard.The values stated in inch-pound may be approximate.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safet
5、y and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD2904 Practice for Interlaboratory Testing of a Textile TestMethod that Pr
6、oduces Normally Distributed Data(With-drawn 2008)3D2906 Practice for Statements on Precision and Bias forTextiles(Withdrawn 2008)32.2 ASTM Adjuncts:TEX-PAC43.Terminology3.1 DefinitionsFor definitions of textile terms used in thistest method,see Terminology D123.3.1.1 The following terms are relevant
7、 to this standard:cross-machine direction,machine direction,pressure,andthickness.4.Summary of Test Method4.1 A specimen is placed on the base of a thickness gaugeand a weighted presser foot lowered.The displacement be-tween the base and the presser foot is measured as the thicknessof the specimen.5
8、.Significance and Use5.1 This test method is considered satisfactory for accep-tance testing of commercial shipments since current estimatesof between-laboratory precision are acceptable,and this testmethod is used extensively in the trade for acceptance testing.5.1.1 In case of a dispute arising fr
9、om differences inreported test results when using this test method for acceptancetesting of commercial shipments,the purchaser and the sup-plier should conduct comparative tests to determine if there isa statistical bias between their laboratories.Competent statis-tical assistance is recommended for
10、 the investigation of bias.As a minimum,the two parties should take a group of testspecimens that are as homogeneous as possible and that arefrom a lot of material of the type in question.Test specimensthen should be randomly assigned in equal numbers to eachlaboratory for testing.The average result
11、s from the twolaboratories should be compared using the appropriate statis-tical analysis and an acceptable probability level chosen by thetwo parties before testing is begun.If a bias is found,either itscause must be found and corrected,or the purchaser and thesupplier must agree to interpret futur
12、e test results with consid-eration to the known bias.5.2 Thickness is one of the basic physical properties oftextile materials.In certain industrial applications,the thick-ness may require rigid control within specified limits.Bulk andwarmth properties of textile materials are often estimated fromth
13、eir thickness values,and thickness is also useful in measuringsome performance characteristics,such as before and afterabrasion and shrinkage.1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.59 on Fabric Test Methods,Gen
14、eral.Current edition approved July 1,2015.Published September 2015.Originallyapproved in 1960.Last previous edition approved in 2011 as D1777 96(2011)1.DOI:10.1520/D1777-96R15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For An
15、nual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4A PC program on floppy disk for analyzing Committee D13 interlaboratorydata are available from ASTM Headq
16、uarters.For a 312-in.disk,request PCN:12-429040-18.For a 514-in.disk,request PCN:12-429041-18.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.3 The thickness value of most textile materials will varyconsiderably depending on the pressure applied to the speci-men at the time the thickness measurement is taken.In allcases,the apparent thickness varies inversely with the pressureapplied.For this reason,it is essential that the pressure
