收藏 分享(赏)

ASTM_C_547_-_17.pdf

上传人:益****师 文档编号:183906 上传时间:2023-03-04 格式:PDF 页数:7 大小:325.16KB
下载 相关 举报
ASTM_C_547_-_17.pdf_第1页
第1页 / 共7页
ASTM_C_547_-_17.pdf_第2页
第2页 / 共7页
ASTM_C_547_-_17.pdf_第3页
第3页 / 共7页
ASTM_C_547_-_17.pdf_第4页
第4页 / 共7页
ASTM_C_547_-_17.pdf_第5页
第5页 / 共7页
ASTM_C_547_-_17.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:C54717Standard Specification forMineral Fiber Pipe Insulation1This standard is issued under the fixed designation C547;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indi

2、cates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers mineral fiber insulation pro-duced to form hollow cyli

3、nders for standard pipe and tubingsizes.Use mineral fiber pipe insulation that has been eithermolded or precision v-grooved,with one or more walls splitlongitudinally for use on pipe temperatures up to 1400F(760C).1.2 For satisfactory performance,use properly installedprotective vapor retarders or b

4、arriers on sub-ambient tempera-ture applications to reduce movement of moisture through oraround the insulation to the colder surface.Failure to use avapor barrier can lead to insulation and system damage.Referto Practice C921 to aid material selection.1.3 Flexiblemineralfiberwrapproductssuchasperpe

5、ndicular-oriented fiber insulation rolls,non-precision ormanually scored block or board,or flexible boards or blanketsused as pipe insulation,are not covered by this specification.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematical

6、conversions to SI units that are provided for information onlyand are not considered standard.1.5 ForNavalSeaSystemsCommand(NAVSEA)acceptance,materials must also comply with SupplementalRequirements.See Annex A1 of this standard.1.6 The following safety hazards caveat applies to the testmethods port

7、ion,Section 11,only:This standard does notpurport to address all of the safety concerns,if any,associatedwith its use.It is the responsibility of the user of this standardto establish appropriate safety and health practices anddetermine the applicability of regulatory limitations prior touse.1.7 Thi

8、s international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(T

9、BT)Committee.2.Referenced Documents2.1 ASTM Standards:2C167 Test Methods for Thickness and Density of Blanket orBatt Thermal InsulationsC168 Terminology Relating to Thermal InsulationC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-

10、Hot-Plate ApparatusC302 Test Method for Density and Dimensions of Pre-formed Pipe-Covering-Type Thermal InsulationC335/C335M Test Method for Steady-State Heat TransferProperties of Pipe InsulationC356 Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soak

11、ingHeatC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC411 Test Method for Hot-Surface Performance of High-Temperature Thermal InsulationC447 Practice for Estimating the Maximum Use Tempera-ture of Thermal InsulationsC585 Practice for Inner and Outer Diameters of ThermalInsulatio

12、n for Nominal Sizes of Pipe and TubingC680 Practice for Estimate of the Heat Gain or Loss and theSurface Temperatures of Insulated Flat,Cylindrical,andSpherical Systems by Use of Computer ProgramsC795 Specification for Thermal Insulation for Use in Con-tact with Austenitic Stainless SteelC921 Practi

13、ce for Determining the Properties of JacketingMaterials for Thermal InsulationC1045 Practice for Calculating Thermal Transmission Prop-erties Under Steady-State ConditionsC1058/C1058M Practice for Selecting Temperatures for1This specification is under the jurisdiction of ASTM Committee C16 onThermal

14、 Insulation and is the direct responsibility of Subcommittee C16.20 onHomogeneous Inorganic Thermal Insulations.Current edition approved Sept.1,2017.Published September 2017.Originallyapproved in 1964.Last previous edition approved in 2015 as C547 15.DOI:10.1520/C0547-17.2For referenced ASTM standar

15、ds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959

16、.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 Evaluating and Reporting Thermal Properties of ThermalInsulationC1104/C1104M Test Method for Determining the WaterVapor Sorption of Unfaced Mineral Fiber InsulationC1335

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2