1、Designation:D 225 04Standard Specification forAsphalt Shingles(Organic Felt)Surfaced With MineralGranules1This standard is issued under the fixed designation D 225;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This specification covers asphalt roofing in shing
3、leform,composed of single or multiple thicknesses of organicfelt saturated and coated on both sides with asphalt andsurfaced on the weather side with mineral granules.1.2 Shingles meeting this specification are intended to beapplied with a headlap of not less than 51 mm(2 in.).1.3 The values stated
4、in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.2.Referenced Documents2.1 ASTM Standards:2D 228 Test Method for Sampling,Testing,and Analysis ofAsphalt Roll Roofing,Cap Sheets,and Shingles Used inRoofing and WaterproofingD 1079 Terminology Relati
5、ng to Roofing,Waterproofing,and Bituminous MaterialsD 3161 Test Method for Wind-Resistance of AsphaltShingles(Fan-Induced Method)D 3462 Specification forAsphalt Shingles Made from GlassFelt and Surfaced with Mineral GranulesD 4977 Test Method for Granule Adhesion to MineralSurfaced Roofing by Abrasi
6、onE 108 Test Methods for Fire Tests of Roof Coverings3.Terminology3.1 DefinitionsFor definitions of terms,see TerminologyD 1079.3.2 Definitions of Terms Specific to This Standard:3.2.1 weather-exposed portionany portion of a shingleexposed to the weather when applied in accordance with themanufactur
7、ers instructions,excluding any part of the upperportion exposed by a cutout.4.Classification4.1 Type IUniform or nonuniform thickness shingles ofany style(see Table 1).4.2 Type IIIUniform or nonuniform thickness shingles ofany style(see Table 1).5.Materials and Manufacture5.1 In the process of manuf
8、acture,a single thickness of dryfelt shall be impregnated with a hot asphaltic saturant,thencoated on both sides with a hot asphaltic coating,and finallysurfaced on the weather side with mineral granules.Laminatedshingles need have mineral granules only on the weather sideof the laminate.The reverse
9、 side shall be covered with asuitable material to prevent the shingles from sticking togetherin the package.5.2 The felt shall be produced primarily from organic fibers.The surface of the felt shall be uniform and relatively smooth.Upon splitting or tearing on the bias,the felt shall appearreasonabl
10、y free of lumps of underbeaten stock and particles offoreign substances.5.3 The asphaltic coating may be compounded with a finemineral stabilizer substantially insoluble in water.6.Physical Requirements6.1 During handling and application,the shingles shall notcrack at ambient temperatures above 10C(
11、50F)nor be sosticky at temperatures below 60C(140F)as to cause tearingor other material damage upon being unpacked.6.2 Loss and Behavior on HeatingThe shingles shallconform to the physical requirements prescribed in Table 2.1This specification is under the jurisdiction of ASTM Committee D08 onRoofin
12、g and Waterproofing and is the direct responsibility of Subcommittee D08.02on Prepared Roofing,Shingles,and Siding Materials.Current edition approved July 1,2004.Published July 2004.Originally approvedin 1925.Last previous edition approved in 2003 as D 225 03.2For referenced ASTM standards,visit the
13、 ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United Sta
14、tes.7.Dimensions,Mass,and Permissible Variations7.1 The style and dimensions of the shingles shall be asagreed upon by the purchaser and the seller as part of thepurchase contract.Shingles shall not vary more than 66 mm(14in.)from nominal dimensions established for each style andsize.7.2 The shingle
15、s shall conform to the masses prescribed inTable 1.8.Workmanship,Finish,and Appearance8.1 The felt(each felt in a laminated shingle)shall bethoroughly and uniformly saturated and shall show no unsat-urated spots at any point upon cutting 50-mm(2-in.)widestrips at random across the entire shingle and
16、 splitting themopen to their full length.8.2 The weather side shall be uniform in finish and texture,but may be embossed to simulate a wood grain.The mineralgranules shall be uniformly distributed in a smooth layer overthe entire surface and shall be firmly embedded in the asphaltcoating.The mineral granules shall not have ruptured the feltfibers as a result of embedment or embossing.8.3 The reverse side coating and the material applied toprevent the shingles from sticking together shall be unif
